Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
Hello, I'm working with the EK PCA10003, that has the NRF51422. I'm trying to read the information of the accelerometer MPU6000 with an ISP interface. At the moment I cannot...
Hi,
I'm working now with the uart connection between NRF52832 and SIM868 module, my question is:
Is there any uart interrupts implementation (examples), i want to receive...
Hi everyone,
I am in the phase of evaluating different chips and need to know the number of PWM channels for the nRF5340 and can't really find this information. The product...
Hello guys. I have six of these boards nrf52840
Do you have any Arduino Bluetooth sample code for using six or seven of these boards in a peer to peer network setup? ...
Hi , i have implemented a event to flash handler with NRF_SDH_SOC_OBSERVER and it work . But I need to know which operation is related to the event , Es: void FlashEvent_Handler...
I am trying to open HTTPS client project from \v1.2.0\nrf\samples\nrf9160\https_client i am facing below error.
I tried opening different project still i am getting same...
Hi,
I followed this thread ( Link ) to implement a simple message model on the light switch example from nRF SDK for Mesh v1.0.1. I created a "send_simple_message" function...
Hi,
Our custom NRF52840 device uses a cellular modem. We communicate with this modem using AT commands.
We will also be hooking up our devices to a custom server that...
Hello,
I have recently purchased an nrf9160-DK for a project I'm working on here in the UK. Having fired it up and realised that the iBasis coverage is minimal where can...
I'm starting to try to figure out a secure OTA process using the 9160 and tools that Nordic has provided in the SDK and I am confused by one thing I'm encountering.
What...
Hi.
I want to test my iBasis SIM card for NB-IoT with nRF9160DK. So, I tested with the "AT_client" example. I have followed "Getting Start with nRF8160 DK" instruction and...
Hi, I am trying to run ble example - uart in segger embedded studio. I am using 11.0 sdk. I have imported keil project into segger embedded studio. I have the error stating...
Hi devzone,
I'm using translation.
I use nRF52840. I created a firmware like the attached one based on the SDK15.3\examples\peripheral\bie_peripheral\ble_app_blinky. ...
Hi all,
I have a custom board with LED on PIN 11 of nRF52832, and I am using SWD P20 configuration to program my board through nrf52 DK PCA10040. Apparently, nRFgo Studio...
Hi
this is not a question - I'd like to give feedback about the peripheral example usbd_hid_generic.
I'm new to 52840 and new to USB. As learning lesson I tried to build...
