Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
Hello, I'm working with the EK PCA10003, that has the NRF51422. I'm trying to read the information of the accelerometer MPU6000 with an ISP interface. At the moment I cannot...
I am using nRF52832 DK.
I am trying to print Battery service value in log file ( Client side ).
So where i get this information and how can i print this information in...
I’m looking for setting up an evaluation network considering of 10-14 nodes as data sources that are to send data values on a periodical basis to a data sink mode that will...
Hi everyone,
I am developing application on nRF52832 using SDK 15.3 on SES, windows. I am using secure DFU bootloader for FOTA process.
Scenario 1 : If I don't use DFU...
Hi Team,
After I add the ANT module into my project, I found the fds_gc() will always return error 1( NRF_ERROR_TIMEOUT ) when it has dirty records. If there are no dirty...
Hi,
I am using NRF51822 SDK12; S130 and trying to qualify Batter level service, So far encountred a problem with Test Case: BAS/SR/DES/BV-02-C, the Verdict is INCONCE all...
Hello, I just got the nRF52832 development board and i was playing around with the examples. I was able to connect it with the nRF Connect app on my mobile and desktop. But...
Central info SDK: 15.3 nRF52840
Peripheral info SDK: 13.1 nRF52832
I want to increase the communication speed after connection. I want to know how to set the communication...
Hi,
I'm trying to measure the power consumption of the nRF52840 chip , which runs the "nimble" BLE stack rather than SoftDevice.
However, the nimble BLE stack runs on...
Dear Nordic Team,
We want to use the FreeRTOS for commercial use, kindly request to answer the below questions.
1. Is AWS FreeRTOS open source & commercially distributed...
Hey all, I'm a beginner to bluetooth,
I ordered the NRF51822 dev kit and it worked easily out of box with my android phone.
I'm creating my own android app to communicate...
Hi Nordic
I want to change mesh-sdk-4.0 LPN example tx output power to 4dbm, including proxy broadcast, mesh packet,
I try to change " RADIO_POWER_NRF_0DBM " in whole...
The Nordic Uart service for peripheral devices has a function ble_nus_init() which takes a callback function in a struct.. Later on this callback function may be called with...
I am doing the project using nrf blinky.
My phone cannot find the nrf52840 . Before this it is ok, but now it cannot discover it . I notice that LED05 is blinking very fast...
Hi guys ,
I am trying to connect thermistor with the ADC pins of nRF.
I use the steinhart formula to calculate the temperature in degree celcius. I used a voltage divider...
