Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
Hello, I'm working with the EK PCA10003, that has the NRF51422. I'm trying to read the information of the accelerometer MPU6000 with an ISP interface. At the moment I cannot...
I'd like to use the GATT/GAP driver from an ARM based Linux system. Is there any possibility of getting a library compiled for ARM or (cough) the source code to build it myself...
I would like to measure BER and PER on custom board by using sample project that is included SDK.
\examples\dtm\direct_test_mode\pca10028\s110
Could you please teach...
Hello,
I'm powering a Readbear BLE nano using a CR2450 coin cell battery. The firmware application is written using mbed. How can I measure the battery level of the CR2450...
hi,
can i use timer interrupt has more than 1ms period??
#define APP_TIMER_TICKS(MS, PRESCALER)
((uint32_t)ROUNDED_DIV((MS) * (uint64_t)APP_TIMER_CLOCK_FREQ, ((PRESCALER...
Hi, I'm trying IOT SDK now and I got some questions
My devices: nRF51422 DK, nRF51_iot_sdk_0.8.0_f1f6187, iot_ipv6_coap_client_pca10028
Q1: Why is the advertising interval...
Hi Nordic support,
I am building the ble_connectivity project of the latest SDK11. My EVB is pca10028m, the project is located under "nRF5_SDK_11.0.0_89a8197\examples\ble_central_and_peripheral...
HI,ALL,
in the Blue Core Spec, there are such statement here,
L2CAP permits higher level protocols and applications to transmit and receive
upper layer data packets...
Hi, I use [nRF5_SDK_11.0.0\examples\ble_peripheral\ble_app_hrs\pca10040\s132],but I get error such as the following.
{
............\components\softdevice\s132\headers...
I read this older post ( devzone.nordicsemi.com/.../) and have a similar issue but with enough differences that I felt it was worth a new question.
I have an STM32 MCU...
HI, I am new to embedded system and just start to learn NRF52 DK. currently I want to configure a pin of nrf52 as interrupt. so i created new GPIOTE_Handler function . however...
hi, i am getting a lot of help in here, thanks a lot
i'm using SDK 6.0.0 for my project. and i want to use timer as a counter like as the title.
then, i fount the app_timer_cnt_get...
hello,
I am using S130 softdevice. While I am trying to connect with MCP I am getting one error with error code :0x08. and MCP is showing a message like "Lost connection...
Hi,
I have a battery powered device which goes to system off mode when it is not used. I want to do some stuff when the battery is inserted the very first time after production...
My application uses the Softdevice, app_timer and app_pwm.
So all timers are in use, but I have to measure two more pwm signals on two input pins.
(Those come from HC-SR04...
Hi,
I'm resetting the chip externally using the reset pin to not be in debug mode. I'm running the system off example here modified to not use buttons.
I have the J...
