Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
Hello, I'm working with the EK PCA10003, that has the NRF51422. I'm trying to read the information of the accelerometer MPU6000 with an ISP interface. At the moment I cannot...
I'd like to use the GATT/GAP driver from an ARM based Linux system. Is there any possibility of getting a library compiled for ARM or (cough) the source code to build it myself...
It is possible to run easily a SoftDevice stack (e.g. S110) on nRF51422 using an accurate 16MHz external clock reference for HFCLK instead of an external 16 MHz crystal oscillator...
Sometimes windows lose the connection to the nRF51 Dongle. The only way I have been able to reconnect to the dongle is by unplugging and replugging it to the USB port. I have...
Hello,
I am currently working on a project where I need to be able to control an RGB by writing the PWM duty cycle to a custom BLE Service and Characteristic. I am using...
When I init, uninit, and re-init a PWM with pin_polarity set to APP_PWM_POLARITY_ACTIVE_HIGH, the actual polarity of the signal is active low. This also happens when I init...
Hello,
I am getting the error code 0x3004, because I am transmitting data too quickly and filling up the transmission buffers.
From other posts, I know the solution...
I'm trying to perform OTA programming with DFU.
when I load only softdevice and bootloader I got address xx:xx:xx:xx:xx:2E
then I load the app with DFU, now the address...
nRF5_SDK_11.0.0-2.alpha.
I create peer by peer_manager.
When initializing the application, i delete them pm_peer_delete_all().
There's an application is stuck.
It works...
Hi
I have a serious problem with stability in "UART" communication over BLE.
I use the command:
err_code = ble_nus_send_string(&m_nus, &bleBuffer, 20);
where I send 20...
I have the following:
Dev board PCA10040
SDK nRF52_SDK_0.9.2_dbc28c9
Mac OSx
I was able to compile the blinky example and have the .hex in the _build folder...
I have several services on a nRF51 peripheral, and would like to have different initialization based on which service is being connected to. The related code is below:
...
Hello,
We have this board ( www.nordicsemi.com/.../nRF51822-mKIT) and would like to use P0.26 and P0.27 as GPIO (or RX/TX for serial). I've cut both solderbridges (SB2...
Hello,
I am having a lot of trouble with connection timeouts. With my current settings (10ms connection Interval and 6 seconds connection supervision timeout) I would not...
Hi,
With the latest nRF Master Control Panel App it's possible to simultaneously scan + advertise on some devices.
I thought this mode is only supported by devices with...
Hello,
am I right in assuming the following?
BLE_GAP_EVT_TIMEOUT with source BLE_GAP_TIMEOUT_SRC_CONN is only returned when a Central is establishing a connection...
Hi, I use Gzll protocol to realize 2.4G frequency hopping communication， Two Device send data to One Host on Pipe1 and Pipe2.
1 Two Devices occur "loss power" many times...
Hi,
I'm working on custom PCB and I have small issue.
After making PCB I was trying to connect, but no luck - "(unable to connect to the target)"
Maybe there is something...
