Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I'm trying to create a PC application to read out some Ti Sensor Tag modules. I'm using a nRF51822 USB dongle and the Master Emulator api.
The nRF dongle sees...
Hi
I have my code like this .
unsigned char *encryptedData;
unsigned int encryptedDataAfterAppendingLength;
memset(encryptedData, 0, encryptedDataAfterAppendingLength...
After ping through link local address ,i am not getting any Router solicitation messages,neighbor solicitation messages and neighbor advertisement messages while i am capturing...
Hi I've got my nRF8001 breakout board ready I now need the SDK in order to start developing firmware code.
I don't have any registration key, how do I get hold of it? ...
Since https://github.com/nrfconnect/sdk-nrf has disabled issues, this is an assorted list of problems/limitations with the lte_net_if library ( https://github.com/nrfconnect...
Hi All,
I want to do dfu over uart with secure bootloader, am using nrf52840-DK, nRF5_SDK_17.1.0_ddde560 SDK and segger embedded studio V8.10.
compiled and flashed secure_bootloader_uart_mbr_pca10056_debug...
I use DWM3001C chip,it has a nrf52833 mcu inside.when i call ble_init() in main.c.it report error:
peer_manager_pds: Could not initialize flash storage. fds_init() returned...
Hi Team, I'm trying to port the acconeer project that worked on the old one NCS v2.2.0 to new NCS v2.5.2 and ran into a problem with the difference
c:/ncs/toolchains/c57af46cb7...
I am trying to use libmodem in a bare-metal app on a 9151dk, but nrf_modem_init() is hanging (not returning). What conditions can cause this? The issue looks a little like...
Hi there.
Right now, I'm facing the issue that I want to use the camera OV7670 with the nRF52833.
I don't know how to start or what example I can take as a base to start...
Hi,
I am using EVB of RAYTAC MDBT50Q-DB (nrf52840 module) for power consumption testing,
I'm running a zephyr application on it, to debug power consumption issues, using...
I have an application where I would like to use ACLK at 12.0 MHz to drive the I2S MCLK signal and create an atypical audio sampling rate (46875 samples/sec). If ACLK is at...
Hello!
Using SDK v2.6.1 and the nRF5340 Audio application, I want to use an external button as button5 instead of the one that is on the board.
I noticed that if i change...
Sometimes I just want to compile a single file for an nRF Connect project with VS Code and the nRF Connect extension. This sometimes fails because an include file isn't found...
Hi.
I am updating an nrf9160 B1 project on a custom board in SDK 2.1.0 to SDK 2.5.3, and I am running into a problem when building. This error does not show up when building...
Hi,
Hello, I have a project that's working great but now I want to extend the abilities of the device by using the extended PHYs. I know there are a so many threads on this...
Hi DevZone!
I'm currently developing a device that has several hardware actuators and I've implemented 2 OnOff Models each belonging to an element. But right now I'm having...
Hello there!
I'm trying to enable secure boot via CONFIG_SECURE_BOOT and am currently getting the following error:
I'm using zephyr via sdk-nrf v2.6.1
Searching the...
Hi,
I just try to use the DFU over USB to upgrade the FW but i found one problem which is the process will erase the external flash data
but i put the some sensor FW data...
