Dear sirs,
Many thanks for the IoT SDK.
Just setting up the Raspberry I can't start the Phyton CoAP example as defined in documentation.
The envirinment is:
R...
Hello everybody,
I'm getting crazy, I'm trying to extend HID axis values from 0..255 to 0..1023 max using the descriptor found in the example ble_HID_keboard/hid_joystick...
Hi, I'm testing the beacon example
(ble_app_beacon, Beacon Transmitter Sample Application ) with my custom board.
I use IAR 7.1 for ARM, Softdevice S110 ver 7.1, and...
Hi,
I'm trying out S130 SoftDevice. I have 1 device with S110v7 which acts as a peripheral.
2nd device contains S130 0.9 (I've based my code on S120 multilink central example...
I've gotten the experimental_ble_app_s130_example_c_pca10028 (BLE Dual role application) to work with my nRF51-DK (modified for my needs). It's an nrF51422 chipset.
I want...
Hey I am working on nordic nrf51822 chip ( http://i.imgur.com/q8EM4uq.jpg ).
I want to run a bluenet code which i have forked from github.com/.../bluenet to github.com/....
Hi, I use the nrf 8001C + stm8s. I successfully installed settings nrfGo, but when I try to execute a command OpenAdvPipe I get an error ACI_STATUS_ERROR_CMD_UNKNOWN .
The...
I am new to this and was looking to upgrade the nRF5340dk and Thingy 53 and using OTA DFU. The documentation I have seen uses the older SDK nRF5. If there is any example or...
We use nRF5340 on our product. We need to update the application/driver/firmware remotely in the field using UART. Now looking through all apps and methods available from...
HI
https://infocenter.nordicsemi.com/index.jsp?topic=%2Fug_nrfutil%2FUG%2Fnrfutil%2Fnrfutil_prod_config_generate_hexfiles.html
Referring to the information on the website...
I seemed to be randomly causing problems to our nRF52840 Zephyr v2.02 sensor's flash.
Previously I had bricked 3 sensors somehow. Before full production, I need to know...
Hello,
I want to implement a vendor-specific service on the nRF5340.
Is there any suitable sample code in NCS 2.2.0?
Or if there is any documentation I should refer...
Hi,
I have a nrf52820 on a pcb without 32Mhz crystal. I am using nrf52833DK to flash the nrf52820 on the pcb using debug out port on DK. I am able to see the connected device...
Hi, it's me, once again. Thankfully the last problem I had was actually my fault... I got distracted and didn't notice a small implementation detail... anyway... Here's today...
Hi,
The customer test routine serial_lte_modem mqtt returns 9,0
What does this state mean?
* ``9`` - Ping response from the MQTT broker.
Thank you for all your...
Hi,
I'm getting the following error during migration from 2.0.0 to 2.1.0:
[505/551] Building CXX object CMakeFiles/app.dir/C_/ncs/v2.1.0/modules/lib/matter/src/app/util...
Hi all.
I'm trying to learn a bit more about the device overlays,
I'd like to know how I would access the "gpio-line-names" that I've specified in my overlay in my application...
Hello guys,
I'm trying to interface nrf52832 with ds18b20 temperature sensor and I'm using this code https://github.com/sigurdnev/Nordic-DS18B20 and I'm getting the output...
Hello,
I am currently having my product, which is based on the nrf52810 SOC, tested and certified. I have been told to set my device up to use the DTM firmware example in...
Hello everyone
I have a few questions about how the nrf chip works: - does nrf52 work by sending AT comman and we need an intermediate chip like pca10040 send AT command...
I am trying to modify the Zigbee light switch example to transmit commands to the first bound endpoint, rather than to a bulb address determined by the app logic:
ZB_ZCL_ON_OFF_SEND_REQ...
