But now I have a new problem that is whenever I set " PWR_UP " bit in CONFIG register then it drop the 3.3 volt vcc to 1.2 volt. I don't know why its happening. Anyway, is...
This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello Sirs
I am using NRF5340 chip in my custom board to use the BLE radio and uart hard ware at the same time. The sample code which has been used for this purpose is ...
I have a BLE device with a MIC, which collects voice data and coded to BroadVoice 32k.
So I want to design a central to get this voice data.
What I think is use 52840...
Hi,
Why do all of these AT instructions fail?
1.AT%XPRODDONE=0
2.AT%XPRODDONE=1
3.AT%XRFTEST
4.AT%XEMPR
Thank you for all your assistance. Kind regards, Peter...
Hi,
Since adding a custom board to a app from a sample, the Flash button:
Has stopped working properly.
When i press it, a build is initiated, but the flash does not...
Hi,
I have been programming my custom board using SWD on a DK. It worked fine when I tried blinky example, however, when I tried nrf_ble_uart example, it stopped at the...
The documentation on how the nrf mesh app adk works is impossible to follow and understand for a junior dev like me to make something close to a working app.
I might be...
Hei!
Mid code development my ability to flash new versions went away. The only clue I have is that W11 installed some new drivers, but I'm grasping at straws. I have screwed...
Hi,
I want to understand that in nCS, where do have BLE abstraction layer..?
As in zephyr device driver model, if you use any peripheral driver API, it internally routes...
I have implemented a custom service with a collection of characteristics. Some of the characteristics require configuration information (sample interval, sample duration,...
Hi,
I've gone through the 4.1.0 Border Router example 3 times now and getting same result of not being able to ping from CLI example.
I am using RPI3B+ with nRF52840...
I am having some issues with spi flash and current. Currently I have the NOR Flash, W25Q128JVPIQ, set up on spi 4 with a FATFS and USB MSD as per customer request. This is...
Is it possible to develop the application on nordic chip(nrf52832) without using the nordic provided SDK but only the soft device(S112)?
The benefit of Coding directly to...
Hello,
we are connecting an NRF9160 with a WFM200 wifi chip over SPI using Zephyr RTOS. Additionally, we manually control the chip select pin in the driver code for the...
Our use case is the following:
We have sleeping nodes, that are time synchronized thanks to an external RTC, and that all wake-up at predefined dates, transmit data with...
I am using nRF_Connect_sdk and RTT logs.
In RTT logs, float numbers are not getting displayed.
I am getting just 0.00 for floating numbers.
Can you help me with how...
