But now I have a new problem that is whenever I set " PWR_UP " bit in CONFIG register then it drop the 3.3 volt vcc to 1.2 volt. I don't know why its happening. Anyway, is...
This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
I have VSCode 1.63.0 (Universal) on macOS 12.0.1 with ncs v1.7.1 and a board with an nRF52840 MCU. I'm using the "hello_world" example. If I power cycle the board I can start...
Hi,
I'm trying to connect to hook-up a debugger in VSCode to my target but am unable to. The hardware is custom and JLink connects fine with nrfjprog to program and erase...
Hi,
I'm trying to ,create a development environment for Alexa gadget in nRF52832.
here is the thing which I'm using:
1. nRF connect for desktop version v3.9.1
2. Toolchain...
I had a Thingy91 that I think I bricked in trying to upgrade the firmware. I'm able to see the device in desktop programming, but it says erasing then gets to a 100% screen...
Dear, I am new to Nordic. I created a simple project for testing. There is a small fucntion to display "Hello World". After , Re-build Solution.. the memory used is as shown...
Dear community,
I am evaluating the nrf52 chip on the nrf52dk. I am using the peripheral_uart example, built for nrf52810. I have stumbled upon an error which I'm not sure...
In our BLE connections we often receive a BLE_GATTC_EVT_WRITE_RSP event with gatt_status 0x01F2.
Looking at the list of GATT_STATUS values, this must be an error in the...
Hi, based on my previous posts ( 2nd post , 1st post ) regarding the ble_app_uart_c multilink example I now face another issue.
When I run the multilink example on my nRF52840...
Hello,
Until now we compiled our company project using SEGGER Embedded Studio command line tool 'emBuild' that was called from a custom Makefile like this:
But we...
Hi all,
I want to self provision my node. I am using nrf52832 dev board, mesh SDK v 3.1.0, light switch client example. You may wonder why self provisioning, when there...
Hi, I am currently utilizing an app that supports multi link; however, I was only able to get 7 maximum stable connections. My goal for this multi-link is to connect a sensor...
Hi,
I am trying to run the DNS example provided in the Nordic Infocenter as part of the Thread Border Router setup, but it is not working. I am getting "Error 28: ResponseTimeout...
Hello,
I tried to implement the HX711 example from Vidar mentioned here ( https://devzone.nordicsemi.com/f/nordic-q-a/34112/best-approach-to-interface-hx711-with-nordic...
Dear, I am developing first project for self training using Nordic MCU. I want to interface few Buttons, Leds and LCD. I read the Datasheet nRF5340_PS_v1.0.pdf. In it in the...
We have selected ble_app_hrs_pca10059_s140 file in peripheral and ble_app_hrs_c_pca10040_s132 in central device, Now we can able to send heart rate value to central board...
