This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
In nRF Connect desktop application, under Bluetooth Low Energy tool v3.0.0, whenever I connect a peripheral device using this application, I see the option to update...
Hi
my application is driving a RGB LED by one wire, this is request a higher sequence , when you drive the RGB LED ,this task can not be interrupt , I am use timer3 to...
Hi all,
I'm working on a project using the nrf52832 with SDK 15.3.0. Our device is battery powered and in peripheral mode. When a central connects it sends +- 300 bytes...
Hello,
I have the Icarus IoT board nrf9160, and I'm trying to connect it to the nrf connect for desktop but it doesn't seem to support the board. I'm getting the following...
Is it possibe to turn on SED on nrf5340 using nRF Connect SDK 1.7.1?
I have problem to turn on.
Here is my code to turn on.
And part of my .prj file
I got error...
I've tried getting nRF53 examples compiling on SES, but it seems there is a bug in SES that is preventing that. It was suggested I try VSCode, despite its lack of debugging...
Hi ,
nRF52810, SDK : 15.2.0, using SES,
I have two questions;
I am trying to add DEVICE NAME to the advertising beacon, in the ble_app_beacon example and following this...
HI,
I succeeded in the test.:SPIM0 SPIM1 SPIM2.
I failed the test SPIM3.
Please help me configure SPIM3 init.
1. The SDK: sdk17.0.2
2. Example: D: \ Project \ nRF5_SDK_17...
I tried to use printf() to get the data from SPI buffers. It runs OK in the peripheral/spi example. But when I moved it to the ble_app_uart, the program stalled at printf...
Hi,
We are looking to upgrade our connect SDK version to 1.7.1 (from 1.5.1) but at the moment there are a few breaking issues for us that will prevent us from doing so....
Hi All,
I have a question that i remark this code run different mode have different results
in Release mode => build success,the project can run
in Debug mode => the...
Hello.
I have couple of questions for hardware parts location on pcb with nRF9160.
Q1.
I'd like to ask a better location for eSIM(MFF2) related nRF9150.
This...
I'm trying to add a second element to (light_switch\server) (SDK_for_Mesh_v5.0.0). I've already have a look at this post , it gives an idea but I found that it's not applicable...
