This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
I have implemented time synchronisation that is based on this example: https://devzone.nordicsemi.com/nordic/short-range-guides/b/bluetooth-low-energy/posts/wireless-timer...
Hello,
I am using Nordic nRF52840 (nRF5SDK v16.0.0) and softdevice : s140.
Nordic MCU is connected to Host MCU over UART interface (baudrate = 115200). I have below observation...
hello,
i am using nrf52840 with sx1276 i am trying to change some of the calls from arduino to nrf52840 can you tell me i am doing everything right
#define DIO0 NRF_GPIO_PIN_MAP...
Hi. I use NCS SDK 1.5.1 with NRF5340 .
I took the project from: \zephyr\samples\portability\cmsis_rtos_v2\philosophers\ as base and try to add two additional tasks.
Application...
Hi,
I would like to implement cell triangulation with the nRF91 in order determine the location of the device via cellular. I already had a look at the available posts such...
Hi friends:
My ble mesh gateway want to remove a mesh node
(a): Which api can i use to realize this purpose?(My SDK is nrf5_SDK_for_Mesh_v5.0.0)
(b): There is a special...
Hi Community! We're happy users of a range of Nordic solutions on behalf of our clients in Europe. Now we're facing a new challenge: one BLE device that should act as a sort...
hello,
i am using nrf52840 with sx1276 module i am using an library which consists of c and c++ files i want to complie both the file but when i complied the following c...
Hello!
I think I have the below problem, except I am using NRF52840 and therefore PCA10056. I am using SDK14.2 and the alpha softdevice. I am aware these are out of date...
Hello everyone, I would like to ask about the examples of openAMP in nrf5340. I only saw examples of network core in nrf\samples\nrf5340\multiprotocol_rpmsg. Where should...
Hi. I am a beginner with nrf52840. Trying to get SPI and an I2C peripheral working at the same time using the SEGGER Embedded Studio. I have working version of both the I2C...
Hello,
I am using the nrf9160 to develop a cellular product but am seeing inconsistent end-to-end connectivity results. For the nrf9160-dk and a custom board based on the...
Some transciver can improve RF performance like output power and EMV, through supply higher DC voltage. Did nRF52840 have the same characteristic with BLE? Is that high votage...
Hello,
I have a questions on the ADC and GPIOs front end input resistance over operational temperature range, as our final product operating temperature shall well beyond...
