Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I'm trying to create a PC application to read out some Ti Sensor Tag modules. I'm using a nRF51822 USB dongle and the Master Emulator api.
The nRF dongle sees...
Hi
I have my code like this .
unsigned char *encryptedData;
unsigned int encryptedDataAfterAppendingLength;
memset(encryptedData, 0, encryptedDataAfterAppendingLength...
After ping through link local address ,i am not getting any Router solicitation messages,neighbor solicitation messages and neighbor advertisement messages while i am capturing...
Hi I've got my nRF8001 breakout board ready I now need the SDK in order to start developing firmware code.
I don't have any registration key, how do I get hold of it? ...
Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hi,
I noticed that if you send AT+CFUN=1 then AT+CFUN=4 more than 30 times in an hour the modem stops registering until the hour passes? Is this by design?
Kind regards...
Hi,
I have built and flashed the "peripheral_uart" example on the nrf52833dk_nrf52833 from nrfconnect sdk v1.5.0. When I build using the prj_minimal.conf file, everything...
Is it possible to manually delete/inject bonding keys when BLE connecting to device with using Nrf52 and pc-ble-driver.py? I would need to execute following scenario:
1...
I have seen a compatibility matrix for nRF52840 SoC at the link below:
https://infocenter.nordicsemi.com/index.jsp?topic=%2Fcomp_matrix_nrf52840%2FCOMP%2Fnrf52840%2Fnrf52840_comp_matrix...
Dear, manager.
Hi,
I am currently testing the use of TWI and BLE together.
However, Data (24bit) is received and read through TWI every 4ms. BLE is only initialized...
Hello,
We are evaluating SDK 17.0.2 USB MSC example.
If we connect the PCA10056 board to USB the Windows make System Volume Information folder,
so if we don't make safely...
Development environment SDK 15.3.0
I am working on overturning the saadc project based on ble_app_uart.
The input frequency is 50~2k Hz.
Terminal and debug monitor...
Hello I'd like to output two PWM alternately. Using the timer, PWM1 and PWM2 alternate outputs every 5 seconds. And I want to change duty cycle according to adc value.
...
hello,
i am using nrf52840 in our customised board and trying to interface it with GDEW0213Z16 2.13 inch display which uses spi communication i have added the necessary...
Hi,
Currently, nRF91 supports only one MIPI RFFE-controlled device. In our solution, we would like to have two MIPI devices - one pair of LTE switches as in Thingy:91 for...
Hi ,
Technical Environment details:
nRF Connect SDK
segger Embedded Studio
nRF5340 DK board
1. I have enabled immutable bootloader and MCUboot bootloader.
...
Hello,
Per the datasheet, VDD_GPIO must be applied after VDD has been applied. Is there a minimum or maximum time?
For example, can VDD_GPIO be turned on 1 second after...
Hi,
I am evaluating nRF5340 for using it in a smart lock product with high security. I had evaluated nRF52840 before this
and was impressed with the integration that the...
I started with the ncs-display-ble-example which worked fine. Next I took the LVGL lv_demo_widget, ran it in the simulator using visual studio 2019 where it ran fine. Then...
