This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hi, in the past, there has been discussed several times whether a peripheral can advertise even when it is already connected/bonded. It turned out it could be possible, however...
Hi, We are working on multiple product based on different MCUs (nRF52832 and ESP32). We would like to use the same Nordic BLE DFU for both of the products so that we would...
Planning to run Packetcraft LEAUDIO stack on nRF52840-DK. This is for evaluation and later on for some development on top of it.
Will it be supported. or is it must to have...
Hi,
I am trying to figure out how serial handling works. Specific questions bolded below. To the best I can see, what I think happens when transmitting is:
NRF_SERIAL_DRV_UART_CONFIG_DEF...
Hi,
I have custom board based on nrf91 but i am going to generate 2 SKUs out of it, the first board consists SIP alone mostly running the SLM application, and my second...
I am trying to capture a signal that transmits upon receiving a polling signal along the same wire.
I have frequented this example but still not having any luck (LED toggles...
Hi,
we have in production an old application developed with SDK13. The application size is growing and with the last update we discovered that during DFU bootloader update...
Hi
I am using an Analog Devices chip as a SPI master and BMD350 (based on nRF52832 chip) as a SPI slave. I want my phone app to send command to the BMD 350 (SPI Slave via...
Hi,
I am testing the UART communication using 2 nRF board, 1 DSP board(test completed with PC).
The code had error, NRF_ERROR_NO_MEM, and I just solved the problem by...
Hello
I use the SDK v17 and the example ble_app_uart and use various functions such as LED, timer, buzzer, etc. I want these functions to work after Bluetooth is connected...
hello ,
i want to perform advertise and scanning at the same time or concurrent. so, for this task i set advertise interval 90ms and scanning interval 105ms and windows...
Hi Guys,
I know there are a lot if topicks about issue with "sd_softdevice_enable". I read them all and nothing help me.
I try to run "nRF5_SDK_17.0.0_9d13099\examples...
Hi,
We're developing a system composed of one device with an nRF running as central, other device with an nRF running as peripheral and desktop and mobile applications...
We are looking for BLE module for Social distancing application.
We want to use Only BLE tags to estimate relative distance with respect to nearby tags within 5 meter range...
