This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
I am using the fatfs example in SDK 15.3 and I need to implement an energy saving mode for a use case when the sd-card is inserted but not needed. In a first step I'm cutting...
Hello, first of all I am new to Zigbee.
I have read the Light bulb example, and now wondering on connecting it with some kind of power consumption monitor. I want to create...
I have been using UART0 to implement a very simple console using console_getline_init() and console_getline().
So the nRF5340 receives commands over UART0 and outputs printf...
We're building a cryptocurrency hardware wallet. And we're using the secure bootloader provided by nrf5 SDK, to only upload signed firmwares to the device. We are using nodejs...
Hi guys,
I am working with nRF52832 board and Zephyr for a short period of time and I really don't have to much experience. Every day I learn some new things and try to...
Hello,
We have a custom board of nRF52832 with two buttons and right now Buttonless DFU is also working perfectly. But, we have scenario where if combination of two buttons...
Please help with writing to flash. If SoftDevice is off all ok. If SoftDevice is enabled, the sd_evt_get function always returns the value 5.
Here is the test code:
Hi!
We are developing a tracker based on Thingy91 using GPS and LTE. We're using the latest Modem firmware 1.2 and Zephyr/NCS v1.2.0
The GPS cold start until receiving...
Hi Devzone!
I'm trying to monitor the battery level of Lithium Ion battery.
I'm using SAADC to check the voltage of 3.7v 3500mAh Lithium Ion battery.
The battery...
when I am waiting for an event the current consumption is becoming ~180uA continuously.
I am waiting for an event using the following function
void deep_sleep(void) {...
Hi All,
I would know, is the NRF52 BLE Mesh Bluetooth 5.0 qualified or not. I did not find it anywhere. As I can see the in Cypress website, they clearly mentioned that...
Can somebody please measure and post the dimensions of the nRF9160 DK please.
Either they are not in the SPEC, or i cant find them.
either way W x L x H - would be appreciated...
Is there a way to specify which AIN should be used through the devicetree API? For example, here is a code snippet:
How would I use the devicetree API to replace the NRF_SAADC_INPUT_AIN6...
Hi
regarding the Nordic guidelines for aQFN, it recommends to use 0.305/0.61 for through hole via.
We are using 0.2/0.4 to avoid soldering bridge and non find any issue...
Hi,
I've tried the Heart Rate sample code (both from hex and source file) and in both cases, I encounter the same problem - constant disconnection. When it finally connects...
