Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I'm trying to create a PC application to read out some Ti Sensor Tag modules. I'm using a nRF51822 USB dongle and the Master Emulator api.
The nRF dongle sees...
Hi
I have my code like this .
unsigned char *encryptedData;
unsigned int encryptedDataAfterAppendingLength;
memset(encryptedData, 0, encryptedDataAfterAppendingLength...
Hi, The DFU process is working correctly and I've tried downgrading the app version which throws the expected error, so it is stored someplace Accessing via the recommended...
Please tell me everyone's knowledge!
I've seen discussions on smartphones that support "LE Coded PHY", but I'm looking for a tablet size.
Is there any smartphone with...
I'm trying to get my nrf9160 DK to communicate with an i2c device so I setup a project to enable the i2c module and use TWIM to send i2c data. But then I run it and it only...
Hi,
I am using nRF52832 S132 SDK15.2
I am developing an application where the development kit which i am programming is a peripheral.
i want this to connect to specific...
Hey All,
I'm running the LTE Link Monitor on nRF Connect 3.3.3. I'm connecting to my custom nR9160 Feather via the built in USB-to-Serial. I'm able to open the serial port...
I tried to drive MAX30003 to get ECG signals through nrf52832.
I use an analog signal instrument to give the standard ECG signals. Now,the nrf's SPI timing sequence is right...
Hello,
The BLE peripheral I'm developing does not have any specific required connection parameters. I understand that the central ultimately controls the selection of parameters...
Dear
I modify the example of PCA10056 mesh light-server for PCA10059 and it works after I program PCA10059 by nRF Connect –programmer go through USB interface. But there...
Hello,
What is the PPM of LFRC?
In our case, the device will remain in low power mode (System ON, wake up from RTC). The device will wake up at every one hour. Which...
Hello Nordic,
nRF52840, SDK16.0, Softdevice 7.0.1.
I'm using LFCLK to generate an accurate tick for device time keeping (with Prescaler=255, Freq=128Hz, Tick=7.8125ms...
Hi all,
I have a problem when I connect the nRF51822 to my phone.
I use the softdevice S130 and the following code attach .
When I use the nRFconnect in my phone, I...
I have a module BL651 and I want to use it in my dev board. I've found in some previous posts that I have to use nrf52 DK to program externally the nrf52810 in my module....
Hi everyone,
I am using nRF52840 to prototype and I want on certain occations to disconnect the peripheral from the central. On of these occations is when I charge my device...
Hi,
I have a mesh network established with one of the nodes being the provisioner. I am currently using Laird BL652. I want to make an android application for the mesh such...
hi support team,
i have one question about 9160 TCP communication, is data re-transmission fulfillment by the modem? how does it work when in psm mode?
for example, when...
