Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
Hello, I'm working with the EK PCA10003, that has the NRF51422. I'm trying to read the information of the accelerometer MPU6000 with an ISP interface. At the moment I cannot...
Can somebody help me out the reason behind below failure on thingy 91. I am building asset tracker example using west on command line. Following is the logs that i got after...
Hi,
I am working on the Thingy91 and trying to set up an event when the USB power state changes (USB cable w/power is plugged or unplugged). For now I will just blink...
Hi,
I changed the softdevice on the nRF52833 light client example from the S113 to the S140, but the program
hangs at startup before even enter the main loop (catched...
Hi ,
During the review, I came across the certification question. After some reading, I found some details.
This got me worried because it looks like it is a difficult...
I have found the example using nRF52833 in the latest SDK (ble_app_att_mtu_through....)
I am using Keil uVision 5.29.0 and I have downloaded the software packs 8.27.1, 8...
Hii,
Our input voltage to nrf52840 is 2 volt, we want to know whether 2 volt will be detected has low(0) or high(1) or undetermined state.we are using gpio pins (1,10) and...
Hello,
I'm considering writing BLE relay application, where central side should bond and encrypt connections (cause sensor device requires it and will not function without...
I'm trying to get the most performance per mA out of my nRF52, for test purposes I've used the nrfx libraries to communicate to the peripherals but I want to make my own....
I want to add a global variable that would increase every time the timer handler is called. I can't get it to work with static, volatile, or even pass on as variable. the...
Dear all,
I am very new to BLE developments and Nordic product, I have purchased the nRF52840 dongle to have a feeling on the product ( I understand I should get the nRF52840...
I have below queries Regarding Secure Boot and DFU:
1) Is the secure boot functionality available in nRF52840, if available please provide the procedure for doing it?
...
Hello, guys!
We are excited to start a new product prototyping by using Thingy:91 board. Consequently, I would have a few questions related to Thingy:91 configuration...
Based on sdk15.3, adding the 0x2902 descriptor to the rx characteristic of the ble_nus service resulted in an NRF_ERROR_FORBIDDEN error.
My code is as follows:
ble_add_descr_params_t...
Hi,
I'm using S112 v6.1.1 with SDK 15.3.0 on nRF52810.( I don't use bootloader )
I tried to search examples for using fstorage api on it.
But I couldn't get anything...
