This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
As the title suggests, I want to use west build without having to include the BOARD_ROOT parameter.
I have already referred to this link , but the results were not as expected...
The ENS210 temperature and humidity sensor connected to an nRF52832 over the I2C interface is not getting ready during initialization. During boot, the ENS210 driver reports...
Hello Nordic Team,
I am working with nRF Connect SDK v3.2.2 on the nRF54L15 DK (cpuapp) and trying to bring up WiFi using the nRF7002 together with the nRF7002-EK connected...
Hello,
I recently received two nRF54LM20-DK (PCA10184) boards and would like to flash the Matter Lock example. Unfortunately, the application doesn't seem to start. I don...
Hello Team,
I am new to nordic products. We have just purchased Thingy: 91x from you. And to flash the latest SDK to Thingy: 91x, I need help.
Like how we can flash the...
Hi,
We have onboarded several hundred nrRF9151 devices using the nRF Cloud "bulk onboard" UI (preconnect onboarding using device_credentials_installer.py ). Generally, this...
Hi,
I have an application with 2 SPI IC connected to the same SPIM port of nRF54L15.
These 2 ICs have different SPI mode:
A: SPI Mode 1 (CPOL 0 CPHA 1)
B: SPI Mode...
Hi,
We are working on a custom design for IoT cellular communication (NB-IoT), using the nRF9151. We've done some testing with the SMA DK, and are at the stage of PCB...
Hi. I am looking into measuring radio channels' qualities by using Energy Detection (ED). But for the examples I've tried so far, I've been getting zero for all the readings...
NCSv3.2.4
Is AoA CTE supported in the nrf52811 ?
Product page https://www.nordicsemi.com/Products/nRF52811 says " The nRF52811 SoC supports Bluetooth LE, and is capable...
Dear Nordic Team,
I am working on a custom board using the nRF5340, and I have configured SPI with the following pins:
SPIM_SCK → P0.08
SPIM_MOSI → P0.09
SPIM_MISO...
I really need to verify this design for nrf54L15 SoC. If someone can go through it and confirm if it is okay or I need to make any changes ? I had made nRF52832 board but...
I am not sure if this is an issue with the nRF Connect extension or the my Thingy91 but when I use the "Flash" button in the actions tab of the NRF Connect extension to program...
I am working with SDK v2.3.0 and a custom board with nRF9160
When I wanted to start my project again after some time, the build configuration had disappeared.
And creating...
I am trying to enable the Channel Sounding feature on the nRF54L15 DK by sending HCI commands over a "USB to UART" interface. For this purpose, I created the "hci_uart" sample...
