Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I'm trying to create a PC application to read out some Ti Sensor Tag modules. I'm using a nRF51822 USB dongle and the Master Emulator api.
The nRF dongle sees...
Hi
I have my code like this .
unsigned char *encryptedData;
unsigned int encryptedDataAfterAppendingLength;
memset(encryptedData, 0, encryptedDataAfterAppendingLength...
I've been tested for BT SIG however have met error which sent 0xc000 and got 0xc000. I expected to receive 0x8xxx. Command is LE_TEST_END in DTM.
I tested with nRF52832...
Hi!
I have old code written in nRF51 enviorment with SDK nRF5_SDK_12.0.0.
I've successfully flashed the softDevice (s130_nrf51_2.0.1_softdevice.hex).
No error occurs...
hi, I am fresher starting my carrier in ASIC i am learning about UART where i come across with the word "DEADBEEF" in the coding please help me with where it is used and how...
Hi We've been using SDK12.1 with softdevice 3.1.0 on a NRF52832 for some time now. Now we want to upgrade our SDK to 15.2 with softdevice 6.1.0. We've converted the application...
Hi all,
I am working on nRF52840, nRF5_SDK_15.2.0, pca10056,usbd_cdc_acm
I can now communicate nrf52840 with PC,However, I failed to connect nrf52840 to android, Android...
Dear Team,
Greetings !!!
Device - nRF52832 Softdevice - s132_nrf52_6.0.0 IDE - segger embedded studio Bootloader - secure bootloader
In our current application, We are...
Hi,
We have build complex application based on Nordic SDK. Right now we are thinking about moving to Zephyr OS. I was wondering if there is any tutorial/tips I can find...
Hi, I'm using nrf52832 development board. In which i have flashed hci_uart example code of zephyr (latest code taken from https://github.com/zephyrproject-rtos/zephyr ) which...
Hello,
Our product is configured to use 3 total GPIOTE channels –– 2 sensors configured for "high accuracy" GPIOTE events, each around 10Hz refresh rate, and 1 using "low...
Current consumption during k_cpu_idle() after GPIO interrupt does not take the same value. Why does this happen? Any idea? Thank you for reading this post in advance.
<Environment...
hi all, i'm using uart with easyDMA, and i'm disabling and enabling it back on my code. before disabling the uart TX and RX works fine. after disable&enable i get wrong data...
Hello,
as part of the development that will soon be in production, I would need to be able to authorize or not the pairing according to an internal state of my device. ...
The memory returned by the pointer returned from cJSON_PrintUnformatted() in below file must be freed.
https://github.com/NordicPlayground/fw-nrfconnect-nrf/blob/master...
I m analysing application source code searching for implementation of INDENTIFY.
The problem is that application has hundrets of classes and it is very complex so it is...
I am developing a product and there is this situation. My custom board doesn't have UART so I will have to communicate over a Virtual Serial COM Port.
I have a desktop app...
