I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I'm trying to create a PC application to read out some Ti Sensor Tag modules. I'm using a nRF51822 USB dongle and the Master Emulator api.
The nRF dongle sees...
Hi
I have my code like this .
unsigned char *encryptedData;
unsigned int encryptedDataAfterAppendingLength;
memset(encryptedData, 0, encryptedDataAfterAppendingLength...
Description:
For my project I'm using 3 Nrf52840 DK, two of them as peripheral and the other as peripheral and central. I'm using also an iOS device as central. The two...
Hello,
I bought a Adafruit Feather M0 Bluefruit LE, the Bluefruit LE module is an nRF51822 chipset from Nordic. I connected the Adafruit board to an accelerometer. This...
Hello, i currently evalutate LTE-M for my company and i run into a lot of trouble for starting the test. But at least i have able to do the test
I have cut a lot of code...
Hi Nordic,
It reads in devzone.nordicsemi.com/.../38040
"According to Section 8.23 in the Product Specification a logical high is between 0.7*VDD and VDD and a logical...
Although BUTTONS_ACTIVE_STATE declared as 1, the hal_buttons_init(button_event_handler) yields an event when the input sees a high to low transition in stead of a low to high...
In testing the timers on the dongle, I have made a GPIO pin be controlled by the timer triggering.
So the following has a constant time between edges:
case NRF_TIMER_EVENT_COMPARE1...
I ran into the same problem as other user one year ago (I was using Arduino Studio nad Segger Studio before), now I switched to IAR (as recommended) and as the examples are...
Using SEGGER Embedded Studio for ARM v4.20a (64-bit).
I'd like to add a new source file to a nRF9160 sample project. The menu selection Project --> Add New File is grayed...
Hi,
I had a custom nRF52832 board. I did some modifications on it. But the same code doesn't run on modified one.
Just to check, Debugging on Segger the yellow arrow(i...
I've been following the guide linked here and got to the point where PCA10090 is flashed with Hello World project. However, when executing "west flash" command, an error appears...
Developing on a custom nRF52832 board, not the Nordic nRF52 dev board, but continue to use version 15.2 of the SDK. Building and download application, but get an abort before...
Hello. I am now implementing communication to multiple peripheral devices based on the multi-roll project “ble_app_multirole_lesc”. (image1)
Central link after setting memory...
Hello,
I am developing an app for Android using the Android-nRF-Mesh Library, available here: https://github.com/NordicSemiconductor/Android-nRF-Mesh-Library
According...
Hi everyone,
I use nrf52840 DK with Segger embedded studio. I have created a project where I read several sensors data and send these data to mobile through BLE UART.
...
