At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
I use SDK15 and ble_app_uart_c example.
static void db_disc_handler(ble_db_discovery_evt_t * p_evt) { ble_nus_c_on_db_disc_evt(&m_ble_nus_c, p_evt); ble_ser_c_on_db_disc_evt...
Hey,
we want to change our product-bluetooth-chip for new products.
In the example the 16 Bit UUID overrides the byte 12 and 13 in the 128 bit ID. Where I could change...
Hello,
I am having interface nRF51 with RF receiver. Output of RF receiver connected with GPIO pin of nRF51.
How can I detect interrupt on gpio pin?
Thanks & Regards...
Hi,
I'm using Secure_Bootloader example of SDK 15.0.0 and I can't get the Logger module to work. I set NRF_LOG_ENABLED to 1, increased memory regions in make file, so the...
Can the esb bugfix timer (currently TIMER_3) be set to another un-used timer without any side effects? I need to implement the async uart from SDK15 and it uses TIMER_3 and...
Is there a simple example which supports LESC Just Works for peripheral mode only? The lesc_multirole example seems a bit too much since that also supports central role. I...
I am sampling 3 sensors using the ADC peripheral, clocking it once every 15us to sample the 3 sensors (3us acquisition time + 2us processing = 5us per channel).
I use the...
hi,
How can i set Destination Address to a particular Mesh Node. so that all message reach that particular Node Only.Since provisioner can set address while provisioning...
how to use app of mesh to send message to node ?
I already got the source code from web: https://github.com/NordicSemiconductor/IOS-nRF-Mesh-Library .
1\ i have add three...
I would like to put a nrf51822 device into system sleep (not off) mode and wake it up (not reset) with a GPIO transition from high to low. I used SDK(nRF5_SDK_12.2.0_f012efa...
Hello everybody, I tried to activate the PHY Coded in the UART Example from the SDK15.1.0 examples.
For this purpose, I have set NRF_BLE_SCAN_SCAN_PHY 4 in the sdk_config...
hello,we are developing NFC on NRF52832 recently,we want to use NFC as a label,T4T,but we have some problems as follows:
1、firstly,we want to develop NFCT by ourselves(not...
hello , i'am working actually on the timer of nRF52840 S140
my timer look like this:
but how to switch from millisecond resolution to microsecond resolution ? ( APP_TIMER_TICKS...
Hi!
I've try to made bootloader/recovery application that should to replace existing run-time application of the device. The F/W file for replacement placed in external...
