But now I have a new problem that is whenever I set " PWR_UP " bit in CONFIG register then it drop the 3.3 volt vcc to 1.2 volt. I don't know why its happening. Anyway, is...
This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi
I have a sample nrf51822 non BLE program (based on flashwrite_example) that successfully writes and reads flash (last flash page) in a loop, incrementing the number that...
Regarding DFU upgrade, I have the following questions（sdk14.2）: 1.nrf52832 will be paired and bound after connecting with the mobile phone, then in the sdk_config.h file NRF_DFU_BLE_BUTTONLESS_SUPPORTS_BONDS...
Hi,
I'm working on customized light switch demo where I'm able to send string data over mesh, I'm using mesh SDK v2.0.1, I would like to have Provisioner node to be also...
Hi,
If I connect supply from laptop using micro USB cable, battery on PDK also gets discharged?
Asking this because in the initial stages of testing PDK battery is working...
Hello, I use nRF52840_SDK_Mesh, when I run the Light_Switch example with the first Client for the first nRF52840 card the 4 leds light up, and it's the same with the Server...
I need add the proxy feature to the pb-remote provisioner. I use pb_remote client example. I have added the proxy feature, it works, but when startes advertising (mesh_adv_start...
Hi, I have decided to use Nordic Ble Mesh SDK instead of old mesh example. but I have only got NRF51 DK Boards. It was configured in order to use with NRF52 boards.
How can...
Hi @ll, I'm using Mesh SDK 2.0.0 with SD 6.0.0. The example everything is based on is the dfu-example (including parts of the beaconing example) I'm now trying to add a connectable...
Dear Nordic Team,
I have practiced the " ble-characteristics-a-beginners-tutorial" on DK board PCA10028, and it worked perfectly. Then I tried to change the user defined...
Continuing to port MESH into an IAR project. We would like to make logging work with IAR. Right now, we get a warning that the "format" attribute isn't supported.
Is there...
The valid master out time for <= 8 MHz is shown as tSPIM,VMO 59 ns. The valid master out time for > 8 MHz is shown as tSPIM,VMO,HS 8 ns. The latter tSPIM,VMO,HS could only...
In simple on/off example, the client can turn on several server nodes in the same group in the same time,
but in serial example mix simple on/off server, the info center...
/* Copyright (c) 2014 Nordic Semiconductor. All Rights Reserved. * * The information contained herein is property of Nordic Semiconductor ASA. * Terms and conditions of usage...
Hi there,
I aam using SDK 14 and using all sectors of FStorage. I am using all the sectors of FStorage to read and write data.
After about 24 hours, I see data corruption...
