This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hi,
After configure IO and RTC I tried to enter into low power mode however the current consumption doesn't decrease until I call again __SEV (); / __WFE (); / __WFE ();...
I am working on a project where I need to transfer the data from nRF52832 to ESP8266 through UART. I made the connections RX to TX and TX to RX.
I am using ble_app_uart_c...
Hello.
I am testing example 'usbd_msc_pca10056' of ' nRF5 SDK v15.2.0 '.
I don't realize how to change the size of the 8 MB mounted device with QSPI from external flash...
i've done nRF5_SDK_15.2.0_9412b96 saadc example.
i changeed channel_config like this
nrf_saadc_channel_config_t channel_config = NRF_DRV_SAADC_DEFAULT_CHANNEL_CONFIG_SE...
Hi,
I have a nRF52840 DK that I want to measure sleep current on, but I find it a bit confusing with all the switches etc. After reading through the documentation I have...
I have a Rigado BMD350 dev board. This has the NFC tag antenna included. I am just trying to get the example code to work on any of the NFC examples. I can't seem to get any...
Hello everyone
i have question
i'vedone nRF5_SDK_13.1.0_7ca7556 SAADC example.
but i can't find where these print statements are come from
Anyone can tell me where...
Hi all, I'm testing ble adv packets loss rate. I am using a simple scanner example in nRF52832 (Softdevice v2.0.0 & SDK v11), the scanner works in passive scanning, no whitelist...
Hi,
This is strange, I am not being able use p0.02 for digital output from sensors on nrf52840-DK but I am able to use all other analog pins for digital output (p0.03...
In our application we are using SDK13 with FreeRTOS by creating two tasks (xTaskCreate), in certain case one of the task need to shutdown the system. We are using nrf_pwr_mgmt_shutdown...
Hi,
I am working from an existing code base where I had to add the s130 softdevice and BLE scanning capabilities. I have an area of flash that stores application data that...
Hi, I am using nRF52840 DK. I need nRF52840 SDK. I couldn't download it from nordic semicondictor's website as it is not responding. Please some help. Best regards, Daisy...
Hello, I am doing some testing with nRF52840 and its CryptoCell 310 and I am trying to produce an ECDSA signature and verify it using mbedTLS.
CC310 Sign & Verify is working...
Hi,
I am developing an android application which involves reading data from memory card through USB cable.I am using Android studio 3.2.1 with SDK version 28 I need to...
