We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I'm trying to create a PC application to read out some Ti Sensor Tag modules. I'm using a nRF51822 USB dongle and the Master Emulator api.
The nRF dongle sees...
Attempting to get up and running with the basic zephyr lvgl demo found in `zephyr/samples/subsys/display/lvgl`. Text appearing on the screen is of poor quality but still legible...
Hello,
We are currently developing a WiFi library and just started on implementing HTTPS and ran into some issues. Since we don't have enough flash and memory for using...
Hi everyone,
I’m currently working on setting up Azure communication using the latest SLM version for PPP (Point-to-Point Protocol) support. Here’s the configuration I’m...
We have a Waveshare display and a npm1300dk and I wanted to know the proper way to add the npm1300's config.overlay file, generated by nrfConnect's PowerUp, to the west command...
Hi,
I faced some issues regarding multiple IRQ_CONNECT being onvoked on the same irq and I went into this post :
LPUART nRF5340 fatal error - Nordic Q&A - Nordic DevZone...
Hello! I am using nRF Connect SDK 2.6.0v. I created a west workspace and i want to make custom board. I took reference from Devacademy nRF Connect SDK Intermediate Lesson3...
Hello Nordic
Use NRF52832 、 NCS 1.6 、“zephyr\samples\basic\blinky” sample.
In hardware, my board doesn't have a low-speed clock, and the reset pin is floating. Therefore...
Can the nrf7002 be set up to have both a STA virtual interface and an AP virtual interface at the same time?
From all the documentation it doesn't specify that only one...
Hello List,
I have an Arduino Nano 33 ble with nrf52840. It is powered directly with 3.3 Volt using 7 Volt and a 3.3 Volt LDO voltage regulator. It is programmed (via the...
I am using nRF52820 and the SDK is nRF5_SDK_17.1.0_ddde560. When setting advertising data, I am trying to enter the chip's BD address for individual identification. Is there...
Hi support Team,
I would like to know the SDK version to be used for nRF54L15.
Is there any link to know details regarding the configuration, flashing and example codes...
So, I follow the zephyr docs ( https://docs.zephyrproject.org/latest/kernel/services/synchronization/events.html )
and define an event as:
However I get the error: ...
Hello Engineer Greeting of the day i am building my product using nrf52833 IC , there are some communication modules connected to the 52833 , i want to cheack lowest power...
Hi currently i am using nrf52840 sdk ver 17.1.0 s140 i am using the sdk flash storage example in .\.\_nRF5_SDK_17.1.0_ddde560\examples\peripheral\flash_fstorage where i am...
Hello, when building the MQTT sample in the nRF Connect SDK, `getaddrinfo()` is returning only -2 when built for the nRF9161 dev kit. I'm using the onomondo SIM that came...