After ping through link local address ,i am not getting any Router solicitation messages,neighbor solicitation messages and neighbor advertisement messages while i am capturing...
Hi I've got my nRF8001 breakout board ready I now need the SDK in order to start developing firmware code.
I don't have any registration key, how do I get hold of it? ...
Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
when ntfx_spis_init() is done , NRFX_ERROR_INVALID_STATE errer occured.
pcb_state is NRF_DRV_STATE_INITIALIZED.
my code is
int cc3235_spi_init ( void )
{
...
Hello, Hardware : nRF5340DK SDK : v2.6.1 Context : Creating a prototype using a Load Cell and transmitting its weight on BLE. Disclaimer : I'm new to the settings subsystem...
Hello,
We are currently helping one of our client develop a product using the nRF5340.
DK versions:
nRF5340-DK
PCA10095
2.0.1
Host OS:
Ubuntu 22.04.2...
I'm a beginner to nRF52840 board, and I'm currently doing the nRF Connect SDK Fundamentals . But I failed to build the Blinky Sample due to the following error:
I'm sure...
I am working with the module nrf5340-DK. I am searching for an example to use the QSPI with the onboard external memory, could you share an example? and the other question...
Hi,
We are planning to move with the nRF5340 + nRF7002 for our upcoming project. We have some queries related to power section which are, 1. can we an use the same power...
This one is throwing me for a loop. We have a very basic NFC component in our firmware that serves up a static NDEF file and wakes the MCU from a system_off state.
We have...
Hello All,
I am programming an nrf52480 using zephyr on a windows machine.
I am trying to write a bluetooth peripheral characteristic, ore specifically to the led...
When using two nRF5340 Audio DKs as bis_transmitter and bis_receiver respectively for the iso_time_sync sample, the iso_recv event is triggered.
However, in the respective...
Hi,
I use nRF52805 chip for BLE tag. FACTOR_MODE pin will be used for production stage. At F/W start point, F/W reads FACTORY_MODE pin, if the pin is high, F/W will enter...
I am trying to program nrf5340 using this command: nrfjprog -f NRF53 --program merged_domains.hex --verify --recover -r
It works fine if readback protection is not enabled...
Everytime I make a call to the usb_dc_ep_write function I get error -22 meaning invalid argument. I have tried everything I can think of. I tried sending a blank packet with...
Hi：
My environment is: nRF5_SDK_17.1.0_ddde560, keil, s113_nrf52_7.2.0_softdevice When using the ble_app_uart example, "Failed receiving NUS message. Error 0x04. " appears...
After discovering that MBEDTLS requires at least 48000 bytes of heap to function, I've had to desperately find some spare bytes to conduct a TLS session over WiFi using a...
