Hi I've got my nRF8001 breakout board ready I now need the SDK in order to start developing firmware code.
I don't have any registration key, how do I get hold of it? ...
Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
So when changing the hci_icp.conf settings to have the configuration below, i get "CMake Error at C:/ncs/v2.6.1/zephyr/cmake/modules/kconfig.cmake:358 (message):" plus the...
My device is peripheral. I added a few lines before the advertisement start in main(). The whole project is in main and simply advertise and get connected and bonded.
...
I want to configure the ESB and nRF21540 chips on the NRF21540-DK. In order to compare the signal gain, I used the nRF52832-DK and burned the Bluetooth routine (without any...
Hello,
I have a project working on Nora B1, which I am testing on nrf5340DK. It is based on the Peripheral UART Sample, programmed with nfr Connect SDK v1.9.1. Now I need...
Hello,
This is probably a dumb question but, I'm having issues with an initial prototype for a product that has been given. The hardware engineer (me) designed and got...
Quick Start can see the board - but says 'Not supported yet'
Load the programmer and select my board: The log looks like this:
19:07:18.801
Initialising nrfutil...
Hi everyone,
I am testing modem shell application (2.6.1) for PPP support.
Here I am building the application using overlay-ppp.conf and ppp.overlay files.
after flashing...
Hello,
I am currently developing a product that is based on a nrf9160 and more precisely with a Thingy:91, this project integrates the tools of Golioth to communication...
Good morning!
I already looked at other questions in the forum but couldn't find any help. I'm trying to implement an example of Https with basic authentication on my nrf9160dk...
Dear sir:
The DAC private key is generated using P256, and the key length is 256 bits, which is 32 bytes.
As below link, why is 68 bytes planned in the factory data? ...
I'm following Intermediate course lesson 1 exercise 2 to use guiconfig.
When I try to open guiconfig,the output in terminal as follow:
How can I fix it?
Now I am using the https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/nrf/samples/bluetooth/direction_finding_central/README.html and https://developer.nordicsemi...
HI
I am developing a product with nRF52832 and NUS's Central and Peripheral.
The basic operation is to transmit key input to the Peripheral's GPIO to the Central via...
Hi, I am using the Nordic NRF52832 with SDK 16.
In my device I want to bond to a single device at a time. If a second device wants to pair and bond the first device bonding...
Hello,
I have issue with my application size which is too big to success DFU.
So i checked the memory content with nrfjprog --memrd 0x0001C000 --n 0x5C000.
I see that...
