Hello! I'm using sdk8 and s110. I want my peripheral device to send data to the central. I doing following steps:
1. initialize service:
void services_init(void)
{...
I am glad that I have successfully used the library from www.libstock.com/.../nordic-semi-nrf24l01-example in a pair of PIC18F45k50 devices. One is acting as a Tx and another...
Hello.
I have had a search but can not find anything so sorry if this has been covered before.
Our company has developed a consumer product using the nRF51822-QFAA-R7...
Hi every one !
I am trying to get working a code that it was working "Ok" 2 years ago.
Currently, I cannot get communication between both breakout boards.
To simplify...
I'm trying to solve an intermittent problem when using the nRF51422 UART with CMSIS-RTOS (RTX) and MDK Networking library (V6.2) (TCP/IP stack).
My questions relate to...
Hi...
When i was working in SDK v6.1.0 i have tried nrfprog.exe to merge and program bootloader, softdevice, application and bootloader_settings file as explained in devzone...
Hello Team,
I am using nrf52840 board which supports ZIGBEE . Setup Details: Zigbee_LIGHT_BULB (nRF52840 DK) Zigbee_LIGHT_SWITCH(nRF52840 DK)
Light Bulb Example
I am...
I try to use Gazell and USB HID to remote wake up my computer. But after compter turns into sleep, the callback function on the Gazell Host Device doesn't being called back...
The hardware I use is nrf52840Dongle, using nrf_dm sample for development. There are a few problems:
1. I have 8 devices, all within communication range, 4 as base stations...
Hi,
When building the Onomondo softsim_static_profile sample using nRF SDK 2.6.1 I get a region `FLASH' overflowed build error for mcuboot_subimage.
c:/ncs/toolchains...
Hi, I get a issue, build error if enabled PGPS in prj.conf:
CONFIG_NRF_CLOUD_PGPS =y
and OK if comment this config
for this project, I used sample/cellular/Location...
I've tried to compile "hello_dect" example using v2.6.1 toolchain and v2.7.0-rc-2 SDK. The sample code is present so I assume the SDK is correct version. However it fails...
Hello.
In the BLE software being developed, the device uses nRF52840, s140 v7.2.0 or v7.3.0, and I am building a system that periodically sends a beacon (ADV_NONCONN_IND...
Hi,
For some reason, all of the VSCode action disappears after building the application with mcuboot using sysbuild on ncs 2.7.0. The application can only be built using...
I need to measure the battery percentage using adc. i have created an application for ADC and its measuring correctly. Now i need to measure the battery percentage of another...
On the nRF51, LO leakage was measured when in receive mode. For 2402~2480mhz, LO leakage was measured at approximately 2745~2836mhz. The nRF52 does not measure LO leakage...
OK, I'm working with the nRF52832 and NCS V2.6.0, and I have two different actions I need to complete at various times with the SAADC:
Every ~ 3 seconds, I need to sample...
Hi,
I'm running some transceiver tests to look at extended broadcast and ISO transfer modes. I am using nrf5340_audio_dk and ncs V2.6.0 to run nrf5340_audio application...
When i try to run or debug the ble app uart example on our own hardware using the nrf52810 there is a fatal error when executing the code.
The example does run on the...
i Used a nrf52840 DK board and zephyr sdk v2.6.0. I'm start the ble advertisement and configure the gpio interrupt on sw1 in low mode flag GPIO_INT_LEVEL_INACTIVE (Low level...