i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
When using nrf51-ble-driver_win_0.3.0 with Visual Studio 2010, after I put a breakpoint in my code, when I try to have the process "continue", I always get unandles exception...
nRF52840
NCS 1.9.1
I have successfully downloaded app_update.bin to flash and rebooted. MCUBOOT copies the new application correctly and it runs fine.
The boot process...
I opened an issue on GitHub, but the NRF Connect iOS repo has not been updated recently. Here is the link: https://github.com/NordicSemiconductor/IOS-nRF-Connect/issues/118...
Hi guys.
I'm using the development board NFR52840DK and I modified the sample in zephyr\samples\boards\nrf\nrfx to use twp buttons, sw0 and sw1.
The sw0 button reset a...
Hi,
I want to use my PC to send some message to dongle via USB, then the dongle send them to certain device via BLE.
If there is a sample that allows PC interacting with...
Hello,
I have tried running Blinky example with some Low Power directives in the code without success. I came here for help then.
The current consumption used by the example...
Hi All,
I am trying to port my current SES project (s140) from nrf52833 to nrf52832. My nrf52832 is spec'd at 512kb flash and 64kb RAM. Any help would be much appreciated...
Hi,
Trying to evaluate the nRF52840DK with Matter examples but none of them seem to compile.
Following error is the result
Building light_switch west build --build-dir...
Hi,
We are using nrf5340 nrf connect SDK V2.0.0 and we are unable to find the brownout detector configuration. For our use-case we want to trigger system reset if supply...
hello Nordic
i work with nrf52832, with ncs 1.7.1 (moving soon to 1.9.2)
i have some issues with my spim clk and i think (not sure) its related to working with spim0...
Hi
I am trying to bring up the Nordic LE Audio example (nrf/applications/nrf5340_audio) and a basic BLE peripheral (nrf/samples/bluetooth/peripheral_lbs) on the nRF5340...
I want to run a single-edned comparator using the 1.2Vref. I cannot find details on a few items. just how to set it up
A) what is the variance on the 1.2V reference voltage...
Here is a warning during build
C:/v2.1.0/nrf/subsys/bluetooth/mesh/shell/shell_utils.c: In function 'shell_model_strtosensorval': C:\v2.1.0\nrf\subsys\bluetooth\mesh\shell...
Hi,
I downloaded Android-nRF-Toolbox and ble library source code from https://github.com/NordicSemiconductor/Android-nRF-Toolbox https://github.com/NordicSemiconductor/Android...
Hello,
My thingy:91 was working nicely, even connecting to nRFcloud. But after updating the firmware to thingy91_fw_2022-09-15_7a358cb7 and Update jitp certificates it doesn...
