Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi,
I'm trying to interface Adafruit 9-DOF Absolute Orientation IMU Fusion Breakout - BNO055 sensor with nRF5340 DK board. Can you please help with the code where I want...
Hi,
I installed NRF connect SDK,
after installation I navigate from NRF connect desktop app -> Toolchain Manager
V1.71 is installed in D:\Nordic_App\Nordic_SDK\nCS...
I'm using VS 1.7.1 on Windows 10, with the nrf9160dk_nrf9160_ns
Playing around with myFirstApp from the VS Youtube Tutorials, I wanted to redirect output to uart2 and map...
I followed the getting started guide for Ubuntu:
https://docs.zephyrproject.org/latest/getting_started/index.html
I can build Blinky, but when building my project I get...
Hey, I'm starting a new project and I think a very good fit for this would be to have all of my code in an application chip and use a nrf52840 trough USB as a connectivity...
SD140
Our Central Application is scanning to connect to a peripheral's MAC address. When the scanned address matches, we call sd_ble_gap_connect(p_addr,..). But, it is...
Hello! I'm trying to reload CMake in an nRF-Connect-SDK project in the CLion IDE. I've been using this guide: https://blog.jetbrains.com/clion/2021/04/using-nrf52-with-cmake...
Hello,
I am writing the device tree for our custom board, which uses an nRF9160 SiP. This approach to configuring the hardware
is new to me, since my experience is with...
Hello,
We are attempting to track down a rare bug in our code that causes the device to occasionally hard fault.
We have been able to catch it three times, twice where...
Hi,
When I connect nRF52833-DK device to the (Windows 10) system, its JLink UART (COM) Port disappears after some time (in about 4 to 5 minutes.) The following screenshot...
hello Nordic
i work with nrf52840 , .. want to move to ncs 1.8
seems that moving to ncs 1.8 forces me to update to zephyr-sdk-0.13.2 (from 0.12.4)
is it really a must...
Hello,
I have added the line CONFIG_DEBUG_PORT_ACCESS=y in prj.conf file and now the project does not open in Segger Embedded Studio (SES).
I am getting this error,
...
Hi,
I am building my Project in an out-of-tree form and up to this point I solely used Segger Embedded Studio to compile our project. I am using a custom board with an nrf9160...
Hi All!
I am using VS CODE studio as an IDE for nrf9160 FW development. Blinky app compiled and work perfectly. But when I compiled the asset tracker/cloud client it gives...
