Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I used nRF52805 module BC805M on my customized board. I can only make the BLE connection for a few seconds or minutes. Then, the connection will be lost. Here are the...
Hello,
I am working NRF52833 Device. I'm new to this platform.
Whether i can read/write into the UARTnode with my own application without using any Nordic UART API's ...
Hello,
I am trying to run the littlefs example with no changes from Zephyr (NCS v1.5.0) on my nRF52840 DK but I keep getting this error "<err> fs: mount point already exists...
Hi, I try to use UART in the template_project. But if I try to use printf UART doesn't work. The project works fine in debug mode. How can i fix the issue?
Hello Everyone,
I am trying to bring-up the UART Application in NRF52833 Device.
I have downloaded "nRF5_SDK_17.0.2_d674dde" file.
Getting below error, while compiling...
I am trying to connect and read the data of the MIO Fuse heart rate band. It is designed as per the Bluetooth SIG specifications i.e heart rate service UUID is 180D and the...
Hi,
A project I'm working on can be seen as a collector of data from many different sources. To keep I an overview I've decided to use C++ objects rather than C (in other...
Hello,
I'm using nRF52833, s140, pca10100.
I looked at the code 'nrfx_saadc.c' to uninit SAADC.
The file contains two types of code, with or without the definition...
Hi,
One of our unit started to systematically report DNS_EAI_SYSTEM (-11) when calling getaddrinfo(). In a attempt to get more info about the error, I added errno to the...
Hi experts
I am trying to play a little with BLE HID keyboard example supplied by nordic
I see that there is an array of 5 characters "hello" + "enterkey press" which is...
Hello There,
I want use I2C in nRF9160 for getting MPU6050 or MPU9250 data in it,
I try this Example with change overlay file in it
SDK 1.5.1 and also try with 1.40...
I am trying to send data obtained from my sensor (calculating with twi scanner example ) via BLE using the ble_nus_data_send function. I just tried to send this data via UART...
Hi,
The eddystone example enter to connectable mode by press a button, but our customer don't want to press button one by one, they hope the beacon can advertise eddystone...
Custom nRF52 device uses SPI interface for external flash, so in order to read/write to external flash would need a RAM loaded firmware to keep code in internal flash untouched...
Hello,
How can I have two or more temperature probes reporting using the ZCL library?
Imagine that I want to have a device that measures for instance two temperatures...
