Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
Hi,
I am using spim3 16Mhz and sometimes the spi tx data had the first byte as same as previous last byte and sensor can not react and timed out because of the wrong data...
Hello,
I am using NCS v1.3.0 and nrf52840 dk board. In the central_uart demo example, there is a macro called "BT_LE_SCAN_PASSIVE" which has an option set as "BT_LE_SCAN_OPT_FILTER_DUPLICATE...
I have had 3 nrf52840 dongles burn out after a few weeks running on 3V from 2x 1.5 alkaline batteries, powering the dongle from VBUS. Initially, the current draw was 900uA...
Hi Team,
I am looking for an isochronous stream feature for one of our application use cases.
I am using NRF52840 now. Will this feature come as an FW/SW upgrade or in...
1. regarding about trying to make the GPIO pin as 1.8V output for nrf52840
I try to make my board to work with theGPIO output 1.8V, I have calling the code below after the...
My understanding is that to re-flash the DK when the PPK is mounted, I need to move the COM switch from DK to EXT.
I can see the location of COM and it appears on one side...
Hi
Anybody knows where we can buy nrf52832? It is not anymore available and the lead time is about 1 year!
Is it any similar IC that we can use in our new design?
...
Hi Nordic team,
Experimenting with nRF NCS v1.5.0, Openthread CoAP.
When the client send a message to server, CONFIG_OPENTHREAD_MTD_SED is enabled, I reduced the poll...
Hi. I need some help to change blink led's on zephyr. I'm using NRF Connect SDK v1.5.0 SEGGER Embedded Studio for ARM Release 5.34a Build 2021011401.44914 Nordic Edition macOS...
Hello I am trying to program an external custom board that has an NRF52832 on it and I'm using the NRF52840-DK (Development Kit). The programming is being done using SWD over...
I am trying to use nrfsniffer to debug connection related issues.
We have a ble connection between central and peripheral and we are sending status updates to the peripheral...
I am building an application nrf52840 SDK v17.0.2 soft device is S140 with Segger embedded studio.
Application is to send advertisement data in one single channel (say channel...
Hi
I am trying to Update the Soft Device from 6.1.1 to 7.0.2 (SDK 15 to 17). Using an NRF52840 Dev Kit I am using nRfgo Studio to:
Erase all
Program the new Soft Device...
Hi
I am trying to Update the Soft Device from 6.1.1 to 7.2.0 (SDK 15 to 17). Using an NRF52840 Dev Kit I am using "nRfgo Studio" to:
Erase all
Program the new Soft...
