Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I'm trying to create a PC application to read out some Ti Sensor Tag modules. I'm using a nRF51822 USB dongle and the Master Emulator api.
The nRF dongle sees...
Hi
I have my code like this .
unsigned char *encryptedData;
unsigned int encryptedDataAfterAppendingLength;
memset(encryptedData, 0, encryptedDataAfterAppendingLength...
Attempting to program an nRF52840 dongle with sniffer_nrf52840dongle_nrf52840_7cc811f.hex, using nRF Connect Programmer v1.4.8, on Windows 7
Upon clicking "Write", the red...
HI,
I am trying to use STTS751-1DP3F temp. sensor with nr52832. The drivers for sensors are given on:
https://github.com/STMicroelectronics/STMems_Standard_C_drivers/tree...
I have some old production code that uses s110 v 5/6 and SDK 8.0.0 (perhaps - no one seems to know). The production device has never been able to do a bonded reconnect correctly...
Hi,
Your online power estimator only concerns nRF52840/832/810.
How to get a value when using nRF5233 with CTE activated for AoA ?
In other words, what is the additional...
I'm trying to create application for working with nRF52 device. I have completed provisioning mesh success, and receive notification message about success operation (work...
I know that SoftDevice 110 is old but I am stuck with it as it is on a production device with nRF51822. For some reason when I call sd_ble_gap_adv_data_set() with a non NULL...
I am developing software with the following features.
Communicates between two boards with nRF52840, nRF5 SDK 15.3.0, and its S140
Activate both extended advertising...
When I use this setup, when the specified duration expires, should I get a BLE_ADV_EVT_IDLE event? I don't seem to get one, even though I'm testing for it. SDK 17.0.2 / S...
Hi,
I have 4 sensors on my custom board and I'm planning to use BLE. I want to read data from all 4 sensors every 200ms. I'm planning to use app_timer for that and read...
Hi
Using demo usbd_cdc_acm and found a very strange bug!
Even I disabled the flow control of uart , the 52840 device still need to control the DTR signal to ensure UART...
Hi Nordic Team,
I am developing a CoAP client on the nRF9160 DK, and am having trouble with longer proxy-uri's; short URIs ( 268 characters and below ) work fine and the...
Hello good people at Nordic. Happy new year!
I am attempting a simple extension of the GPIOTE example in the SDK. I want to measure the time duration of the generated pulse...
I'm sure the mistake is mine but I would appreciate some suggestions on where to look for my mistake.
I have a custom board with a Fanstel BM832A module. I also have an...
