Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
Hello, I'm working with the EK PCA10003, that has the NRF51422. I'm trying to read the information of the accelerometer MPU6000 with an ISP interface. At the moment I cannot...
I'd like to use the GATT/GAP driver from an ARM based Linux system. Is there any possibility of getting a library compiled for ARM or (cough) the source code to build it myself...
It is possible to run easily a SoftDevice stack (e.g. S110) on nRF51422 using an accurate 16MHz external clock reference for HFCLK instead of an external 16 MHz crystal oscillator...
Hi
First the fundamentals, I am using:
nRF52840-DK
nRF Connect for VS Code: v2024.7.13
I am trying to create a demonstration project, where I need both SPI and...
I am currently working on a project where I need to connect my nRF52833 microcontroller to other devices using the Nordic UART Service (NUS). I am using the nRF SDK and Segger...
Hi
I'm having an issue with my NPM1300. drawing high current. I've had 50 of these boards fabricated and the majority are fine, but with the same hw configuration, same...
Currently, I'm using nRF5340 Audio on a homemade board, and I've managed to get the sound input from the gateway as a LINE input and the sound coming out of the headset, but...
Hello, I.m using SDK 2.6.1 with VSCode.
I created a new application based on the sample /nrf/samples/net/mqtt configured for nRF9161_ns which is listed as a compatible board...
Hello! I am a newcomer to nrf and embedded programming (other than basic arduino and micropython projects). So far I have gone through many of the devacademy walkthroughs...
I cannot get the nrf5340 audio dk kit to work from USB input properly. After a reset, it only works for a fraction of a second and audio stops. Has anyone run into a similar...
Hello,
I'm trying to do an HTTP multipart POST with chunked transfer encoding but am having trouble sending the headers to the socket. When trying to send, I receive a ...
I have three nrf5340 board. Now i want to use one as bis-headset and two as bis-gateway. I want to get two audio from two bis-gateway at the same time. Can i do it? How ?...
I am using an IMU sensor in sensor hub mode (LSM6DSV16X, LIS2MDL) with the FIFO interrupt interval set at 30 Hz. The data is sent over BLE. It works perfectly when using RTT...
this is the last log message from monitor thread, I never got any error message from the thread.
00 > [ 01:37:03.890 , 808 ] <dbg> monitor: print_die_temperature: CPU...
Hello again folks,
Recently, I closed a ticket regarding MCUBoot, DFU, and the USB Mass Filesystem. Unfortunately, I'm still having problems. That ticket, for the curious...
With nRF7002DK and TF-M (nrf7002dk_nrf5340_cpuapp_ns.conf) configuration, the sample project works for example.com:
*** Booting nRF Connect SDK v3.5.99-ncs1-1 *** HTTPS...
In my last question, devzone.nordicsemi.com/.../can-cis-and-bis-modes-work-at-the-same-time-or-switching-freely , I have asked that if the CIS and BIS modes can work at the...
During my test of the nrf5340 audio application which in the V2.6.0 SDK , Because of that i need to implement some algorithms in it, i use the ld file to allocated a segment...