After ping through link local address ,i am not getting any Router solicitation messages,neighbor solicitation messages and neighbor advertisement messages while i am capturing...
Hi I've got my nRF8001 breakout board ready I now need the SDK in order to start developing firmware code.
I don't have any registration key, how do I get hold of it? ...
Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
As the title suggests, I want to use west build without having to include the BOARD_ROOT parameter.
I have already referred to this link , but the results were not as expected...
The ENS210 temperature and humidity sensor connected to an nRF52832 over the I2C interface is not getting ready during initialization. During boot, the ENS210 driver reports...
Hello Nordic Team,
I am working with nRF Connect SDK v3.2.2 on the nRF54L15 DK (cpuapp) and trying to bring up WiFi using the nRF7002 together with the nRF7002-EK connected...
Hello,
I recently received two nRF54LM20-DK (PCA10184) boards and would like to flash the Matter Lock example. Unfortunately, the application doesn't seem to start. I don...
Hello Team,
I am new to nordic products. We have just purchased Thingy: 91x from you. And to flash the latest SDK to Thingy: 91x, I need help.
Like how we can flash the...
Hi,
We have onboarded several hundred nrRF9151 devices using the nRF Cloud "bulk onboard" UI (preconnect onboarding using device_credentials_installer.py ). Generally, this...
Hi,
I have an application with 2 SPI IC connected to the same SPIM port of nRF54L15.
These 2 ICs have different SPI mode:
A: SPI Mode 1 (CPOL 0 CPHA 1)
B: SPI Mode...
Hi,
We are working on a custom design for IoT cellular communication (NB-IoT), using the nRF9151. We've done some testing with the SMA DK, and are at the stage of PCB...
Hi. I am looking into measuring radio channels' qualities by using Energy Detection (ED). But for the examples I've tried so far, I've been getting zero for all the readings...
NCSv3.2.4
Is AoA CTE supported in the nrf52811 ?
Product page https://www.nordicsemi.com/Products/nRF52811 says " The nRF52811 SoC supports Bluetooth LE, and is capable...
Dear Nordic Team,
I am working on a custom board using the nRF5340, and I have configured SPI with the following pins:
SPIM_SCK → P0.08
SPIM_MOSI → P0.09
SPIM_MISO...
I really need to verify this design for nrf54L15 SoC. If someone can go through it and confirm if it is okay or I need to make any changes ? I had made nRF52832 board but...
I am not sure if this is an issue with the nRF Connect extension or the my Thingy91 but when I use the "Flash" button in the actions tab of the NRF Connect extension to program...
I am working with SDK v2.3.0 and a custom board with nRF9160
When I wanted to start my project again after some time, the build configuration had disappeared.
And creating...
I am trying to enable the Channel Sounding feature on the nRF54L15 DK by sending HCI commands over a "USB to UART" interface. For this purpose, I created the "hci_uart" sample...
