I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I'm trying to create a PC application to read out some Ti Sensor Tag modules. I'm using a nRF51822 USB dongle and the Master Emulator api.
The nRF dongle sees...
Hi
I have my code like this .
unsigned char *encryptedData;
unsigned int encryptedDataAfterAppendingLength;
memset(encryptedData, 0, encryptedDataAfterAppendingLength...
I'm working on porting a project plus bootloader from SDK 12.2 to 15.3. I have the application working fine, but the bootloader is having some issues. Most of the searches...
Hello there,
i am using the nrf52dk and want to program a selfmade breakout board which includes the BMD-340-ar Bluetooth module from rigado.
I use Segger Embedded Studio...
Hi,
I am trying to extablish TWI communication between 2 nRF52832 devices. One should be master and other slave.
For TWI initialization in nRF52 master, I have below source...
Hello!
I'm new to the nRF52 and to ANT, so I'm in the process of running through some of the example code. I've been able to successfully run blinky example. However, I...
I have an nrRF52832 central connecting to 16 (nordic-based) peripherals. We allow up to 20 connections on this design, but only 16 are currently connected during this test...
Hello,
I'm working on a project and we're using the nRF2840 to get data from a BNO080 IMU.
Someone already wrote arduino code which works. How does one change the sample...
Hi, i'm working a BLE gateway with NRF52DK and S132 by using the demo example central uart.
The peripheral equipement advertise manufacturer data like this:
0x0001 during...
Hi there,
I am new to the Bluetooth mesh and I am learning about it. I have some questions about Bluetooth mesh. I hope you will help me with this.
Please pardon me...
Hi
I am trying to implement the communication between nrf52832 dk and nodemcu esp8266 over i2c.
My i2c code in nodemcu is working fine as I had tested the communication...
Using latest download of nrf Command Line Tools and a J-link Plus unit with Tag-Connect interface. Power on, all connections seem good. Trying to upload a .hex file through...
Hello, I am trying to implement some Bluetooth mesh functionality on my Thingy:52, and it's quite a daunting task.
I am using the mesh sdk v3.1.0 thingy:52 sdk v.2.1.0 and...
Dear All,
Could some one help to answer my commented questions below ? thank you so much !
1.
//Definition at line 743 of file hal_nrf.c .
uint8_t hal_nrf_read_reg...
Dears,
I am trying to implement a peripheral device which behaves like this:
1. within 30 seconds after powered up, the device can be discovered and connected by any other...
Hello,
I am using BLE+MCU MBN52832 module and i am facing one issue while programming my application.
I am uploading the hex file using nrfGo Studio and when i try...
Hi Nordic:
We are using mesh-sdk2.2, our application need a device can subscribe many group address, at the most we need 16 subscribe address in a model,
1. I'd like...
