Hello,
I'm trying to create a PC application to read out some Ti Sensor Tag modules. I'm using a nRF51822 USB dongle and the Master Emulator api.
The nRF dongle sees...
Hi
I have my code like this .
unsigned char *encryptedData;
unsigned int encryptedDataAfterAppendingLength;
memset(encryptedData, 0, encryptedDataAfterAppendingLength...
After ping through link local address ,i am not getting any Router solicitation messages,neighbor solicitation messages and neighbor advertisement messages while i am capturing...
Hi I've got my nRF8001 breakout board ready I now need the SDK in order to start developing firmware code.
I don't have any registration key, how do I get hold of it? ...
Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hi,
We are running an application using REG1 only in DC/DC mode, REG0 is disabled. I believe we've found a small issue with our decoupling of all the power pins, but I'm...
Hello,
I am trying to connect my nRF9160 but am running into some trouble. Only LED 3 blinks for about 3 minutes and then just stays on without blinking; LED 4 never blinks...
Dears
I double the ble_nus_init as below ,I can get 2 service bouth have 2 characteritic.
as below:
err_code = nrf_ble_qwr_init (&m_qwr, &qwr_init); APP_ERROR_CHECK...
I am facing issue with programming of own developed nRF52810QFAA board. I used Pins 25 (clock) and 26 (data) along with Vcc and Gnd to flash device. I tried with two boards...
Hi, May I use slip library code for commercial? I have a project that uses an MCU communicates with an NRF52 BLE module. To upgrade program of BLE module, I flash the bootloader...
I’m mitgrating from nRF52832 TO nRF52810 and softdevice s132 to s112 and having compile issues.
I understand that NRF peripheral has been removed on the nRF52810 but I do...
This how i make it happend:
1.programe softdevice and bootloader.
2.generate app dfu package.
3.upgarde app via nRF Toolbox
4.It's running, all things is seem ok....
Hi, I've been working with SDK11, and now I have to move my project to SDK14 due to some issues with the old SDK. In SDK11 I could just use Keil's "Manage Run-Time Enviroments...
Hello,
I am trying to execute the SPI slave example from sdk15.2 on my NRF52832 Dev board (PCA10040 1.2.1).
I am using stm32f0 dev board as the master and transmitting...
Let suppose using the dynamic multiprotocol ZigBee + Softdevice application with OTA upgrade possibility. I would like to use the app_timer (along with app_scheduler) to trigger...
I want to change MIN_CONN_INTERVAL and MAX_CONN_INTERVAL values when I connected to phone.
I build function that handler events and send the update to ble_conn_params_change_conn_params...
Hi Nordic DevZone,
I am trying to include the UART driver module (.c .h file pairs) into my new project in SEGGER Embedded Studio.
I have done the following:
I...
Hi,
I have a few issues with flashing the dongle. I am using [ \nRF5_SDK_12.3.0_d7731ad\examples\peripheral\blinky\pca10031\s130\arm5_no_packs ]
When flashing the soft...
