But now I have a new problem that is whenever I set " PWR_UP " bit in CONFIG register then it drop the 3.3 volt vcc to 1.2 volt. I don't know why its happening. Anyway, is...
This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello,
I am using an NRF52832 on a Custom Board that i built myself.
I want to communicate with a PC software via UART so i've connected the TX, RX and GND ports to the...
I have a product deployed in production that uses RSSI on BLE advertising channels (37/38/39) to determine rough proximity of beacons to various anchors (scanners). An issue...
Can anyone tell me how to copy binary data to an arbitrary address on a PCA10056 dev board? My project is based on the BLE keyboard example but it also streams audio to another...
Hi!
nRF52832, s132, 6.0, SDK15
I have strange behavior with delete all bonding devices include HID bonding.
Step by step:
I transfer HID keyboard project to my project...
Hello,
I'm not posting this as a problem, but rather to get some suggestions and ideas about this feature. I have a device based on the NRF52832. It is meant to work as...
Hi
What is the role of RESULT.MAXCNT ?
As the scan mode is based on the number of channels with PSELP != 0 isn't MAXCNT redundant ?
Also, If declaring the buffer as...
Dear Nordic,
what is the maximum distance get from a long range BLE?
I heard 1km achieved through long range in open space is it right?
what is the minimum distance...
Dear support,
I'm using the NFC pairing on SDK 15.0.0 on PC10056 PDK. I install the micro-ecc library and the example works.
First question: The coupling between smartphone...
Hi,
I am using nus service to send and receive data between Android App.
After connection established, App send some data to my module and ble_evt_handler get that data...
Hi,
I am using SDK 15.2.0 in nrf52840, pca10056 and s140. I want to combine two codes of SAADC and ble_app_uart. I have added every driver files and path for these files...
Hi, I started a 4 layers PCB design in cad-soft Eagle. In nrf52840 ref design they are using blind vias in 1 to 2 layer, so I'm guessing below DRC layer setup is correct for...
Dear Nordic,
I want to test BLE Mesh network. for that one board(nrf52832 DK board is programmed with client example. when i debug the program its entered into app_weak_errors...
Hi
I am using nrf51822 , sdk version 11 and softdevice version 130
In project I am trying to disable SPI1 and TWI0 channel by using following command
NRF_TWI0->ENABLE...
Hi, I are using BT832 module based on NRF52832-QFAA IC in an application. Please provide the following details regarding ble transmission of NRF52832-QFAA-R7 IC
1) modulation...
Hello,
I´ve got a corrdinator, which establishes my network. Also I´ve got an End-Device that joins the network successfully.
Is there any chance for me to observe the...
