Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I'm trying to create a PC application to read out some Ti Sensor Tag modules. I'm using a nRF51822 USB dongle and the Master Emulator api.
The nRF dongle sees...
Hi
I have my code like this .
unsigned char *encryptedData;
unsigned int encryptedDataAfterAppendingLength;
memset(encryptedData, 0, encryptedDataAfterAppendingLength...
I've downloaded both v15.2.0 and v15.3.0 documentation packages and the pages that reference svg images do not render in Chrome (for example ./nrf5/iot_intro.html). When I...
I am using the nRF52840 dongle to gather data via peripherals and send it via a serial port similarly as the cli example, for that I'm using the nrf_cli_fprintf() function...
Hi all.
I want develop device with nRF9160. goal - to get smallest size with chip antenna.
I not so good in RF design, so usually I using recommendation from datasheets...
Hello,
We have an nRF9160 DK and have successfully set-up the tools necessary to re-flash and write firmware for the DK using Zephyr and SEGGER Embedded Studio. We are planning...
Hi
I have tried to pull down the updates for the Zephyr project to for the mqtt_simple example. when I do a git checkout master and a git pull all goes fine. but when I...
Sir,
I have seen example pgm for communication between UART and BLE, and another pgm which communicates between 2 UARTs. But for my project I need 2 UARTs and the BLE together...
Hey,
previously working with BLE devices I had manage them reading/writing its characteristic. To control my new device I have to write the value into its handle ( i. e...
Hello Sir,
I have a PCA10090 (nRF9160) DevKit and it was working fine with Asset Tracker Example. Kit sent data to nRF Cloud last month. Today i have again verify the...
Hi, I developed a simple app that connects to a Bluetooth device, receives some data from that device and output it to the uart. As a receiver I have a custom board with a...
I have to develop a project for nRF51822 but I can't find tools that work. I tried SES and Eclipse and none can compile the examples of SDK12 (the last one that supports my...
Hello,
I've recently purchased the fanstel BT840F evaluation board which is based on the nRF52840. I understand that you cannot directly program the BT840F evaluation board...
Hi!
I just saw the MQTT example that has been merged in the master branch and tried to run it on my DK (NB-IoT). Without changing anything in the code or configuration the...
Following my last post a few days ago, I was finally able to communicate with a slave via the TWI interface, thank you very much for your help! This time, I have a problem...
Hi,
I'm using nrf52832 as host and peripheral concurrently, with soft device s132. I know that peer manager can handle both host and peripheral.
I now have a need to remove...
Hi everyone,
We are (still) in the process of evaluating the nrf9160 with the DK.
Our use case is the following one: we want the nrf9160 to send periodic messages in PSM...
