After ping through link local address ,i am not getting any Router solicitation messages,neighbor solicitation messages and neighbor advertisement messages while i am capturing...
Hi I've got my nRF8001 breakout board ready I now need the SDK in order to start developing firmware code.
I don't have any registration key, how do I get hold of it? ...
Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
I have ported the NFC URI example to a custom project that I am working on (platform details listed below). I am using an Android phone running NXP tag info app to read the...
Hello
I have a question to ask, I want to beacon the battery level and temperature. I know there is a temperature sensor inside, if I want to use saadc to get the sensor...
Hi All,
I compiled Keil UART application and it is working fine on Eval Board. But the same code I started running on customized board and here am getting only 1 byte every...
Hi there,
I am adding schedule to my application calling app_sched_event_put() inside a context interruption from Button to enable a sequential write to a memory using SPI...
Hi,
I’m trying to use the SAADC on nrf52832. I’m not using softdevice (I’m not doing BLE code) but it’s present on the chip (to use it for DFU). When I program the chip...
Hi I am using the nrf51422_XXAC device. I want to make a connection with my app alone. other apps should not be able to connect. please help me with sample code. I am new...
Hello,
I'm having issues trying to connect to a third-party peripheral (called iTag from now on).
I have an NRF52832-based device running as a central. My device is running...
Hello Nordic Devzone,
I have a few queries regarding using VID& PID for a hardware.
Is there any cost involved when using the Nordic VID & PID?
Will Nordic provide a...
Hi all,
I successfully ported the Semtech’s LoRaMac-node (from official GitHub, master branch) to a custom assembly of two dev boards : the NRF52832 (Dev Kit PCA10040) from...
Hello.
I have a nRF9160DK.
I want to try this uart example: https://github.com/Rallare/fw-nrfconnect-nrf/tree/nrf9160_samples/samples/nrf9160/uart
I want to config the...
Hi everyone,
I want to transmit a HEX array I read from a peripheral using SPI communication (I initialize my RX_BUF in the SPI_EVT_HANDLER() function) via BLE. I am using...
Hello All,
I am working on nRF52810 custom board. I used segger studio in windows 7. For reference i used nRF52 SDK 15.2.0.In my application i used i2c peripheral.
My...
Hello,
as I understand the accuracy of the LF Crystal oscillator for the nRF52832 development board DK_PCA10040 ist set within the sdk_config.h in the following way:
...
Using NRF52832 on a custom PCB with 32kHz + 32MHz crystals, very close to the reference schematic
Using NRF52 15.2.0, S132, arm5_no_packs, Kiel uVision 5.23.0.0
The example...
Hi, I am using nRF52832 with sensor and Softdevice S132 v3.0.0 to advertising packets .I The sensor is interfaced with nrf52832 using twi interface. I am updating advertising...
