We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I'm trying to create a PC application to read out some Ti Sensor Tag modules. I'm using a nRF51822 USB dongle and the Master Emulator api.
The nRF dongle sees...
I want to save Power by disabling the SD Card. VCC of the card is already regulated with an external MOSFET switch and controlled by a pin of the nRF. The problem now is,...
Hi,
I'm currently using SDK 14.2 (on 840) and SDK 15.0 (on 810) with the UART example.
I'm trying to implement the following system.
The Device only receives data...
Hi all,
I'm using SDK 15, nrf 52840, win 7,
The USB cdc example works fine for me.
Yet, when I moved the code to my project the driver is not set by win 7.
On device...
hi Support Team
I am working on Asset Tracking project.Looks like Bluetooth Mesh is more oriented towards controlling.
I have a Ble device Emitting some Data. (say A)...
Hello there,
I have developed simple coap client and simple coap server based firmwares on nRF52840. My hardware/software configuration is:
SDK: nRF5_SDK_for_Thread_v0...
Dev Env
- SDK: v12.1, SoftDevice : S132 v3.0.0
- NRF52 start program : ble_app_uart_c
1. Is it possible to connect to NRF52832(Central Mode) from Android(Phone Pheripheral...
Hi,
While using sniffer and wireshark, I find the issue below.
CRC value of the raw data and the decoded are not the same at all ?
I find this with nRF5_SDK_15.0.0...
Hello!
I have some problem to generate the right service.h file with nRFgo Studio. I used the help in nRFgo Studio and tried several configurations. Sometimes I could connect...
Hi,
I am facing a frustrating problem in my project: I am using Nordic nRF51822 running on UART application SDK 11. The problem comes to when I add peer management and DFU...
Hi,
I am trying to build the connectivity firmware for a custom dongle based on the nrf52832. I am getting a section overlap issue when I am trying to build the solution...
Hello,
I am trying to fabricate a board based on the Thingy design, including the accelerometer.
I positioned the components, traces, vias and pads following some...
hello Nordic Team
I am using 2 DK
One with Light Switch Proxy Client
Another with Light Switch Proxy Switch
I am using Mobile Mesh App 1.0
Client Provisioning I...
I have been trying to use the nRF Connect app on my Apple iPhone in order to get the Current Time Service.
I bought a Arduino Primo that has an nRF52 on it.
The example...
I am working with an nRF51822 IC revision 2 chip and S110 SD 6.2.1 with Keil 5.10. My version of Keil 5.10 will not recognize the chip. I think that this is because I cannot...
Hi,
I am using nRF52832 microcontroller in project.
I use SPI interface for serial EEPROM.
I could able to see write packets are getting transmitted and verified the...
