We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I'm trying to create a PC application to read out some Ti Sensor Tag modules. I'm using a nRF51822 USB dongle and the Master Emulator api.
The nRF dongle sees...
Hello to all,
I am using nRF52832 sdk15.0 version with SES IDE. I want to find adverting with short for e.g.--->
we have BLE app_uart peripherals and one multilink central...
Dear Nordic engineer,
Here is a question when we use the chip's automatic response function, the MCU PRX can download the packet, but PTX can not receive the ACK signal...
Hi.
I'm busy to add the nrf8001 BLE module to my PIC32MM product for negative pressure monitoring in a small area. Is there is list of minimum settings that is available...
Hello,
I'm having issues with the advertising module in SDK 15.0. I basically want the device to fast advertise for 3 minutes and then switch to slow advertising forever...
When I configured POWER_CONFIG_DEFAULT_DCDCEN =1, I found almost no change compared to the case of dcdc, but when I added APP_ERROR_CHECK(sd_power_dcdc_mode_set(NRF_POWER_DCDC_ENABLE...
Quite a generic FreeRTOS question probably here but... on an interrupt, what's the stack the ISR uses? Is it the one from the stack that got interrupted? If so, I guess that...
HI!
I'm using two nRF52840 boards to communicate using ESB. The ESB API doesn't have a pairing protocol so I figured I'd write one without encryption or any bells and...
Hi all,
when I insert ble_nus into mesh_gatt . I realized there are two pulse functions with the same function:
and
if they let them coexist , when I use nrf_connect...
Hi
Using the iOS 'nrf Mesh' application I can provision a PCA10056 succesfully.
I have written fimware image that sniffs for mesh related becaons, and when I power up...
I want advertise data only change with uuid for every 100ms I gone through the nrf 51power consumption guide I guess its same for nrf52 any help for changes or must have points...
Hi,
I'm using multilink Central device with SDK9.0 and stack S130. I'm able to connect to multilink peripheral device as expected. But i am not able to connect to a Custom...
Hi, is it possible to check the current configuration of a GPIO pin? I mean if the pin is currently configured as input or output. Next I need to uninitialize it and reinitialize...
Hi,
the Nordic nRF-series SoCs have got the restriction, that the power has to rise from 0 V to 1.7 V in 60 ms for a guaranteed POR. In our application we cannot guarantee...
We use nRF52832 on our product. We need to update the application remotely in the field using smartphone with BT. The unit in the field will already have an app running on...
