After ping through link local address ,i am not getting any Router solicitation messages,neighbor solicitation messages and neighbor advertisement messages while i am capturing...
Hi I've got my nRF8001 breakout board ready I now need the SDK in order to start developing firmware code.
I don't have any registration key, how do I get hold of it? ...
Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
Hi BJorn,
I am using nRF52840 chipset using NINA-B301 EVK and could port and test some test applications using NRF52 SDK. My query is in actual harrdware we are using only...
In the nRF52832 Product Spec v1.4 th the ere are discussions in sections 16.5 and 19.3.10 about being able able to output a divided down version
of the 32MHZ clock on the...
I'm using nRF52 and SDK 15.2 with SPI Manager (NRF_SPI_MNGR_ENABLED) with EasyDMA disabled. Some of the external chips I'm communicating with via SPI can't handle consecutive...
Hi,
I am trying to write a I2C read and write wrappers for Invensense MPU9250. Previously, I was using SDK11 and I don't have any issue with it. However, after porting...
Hi,
I am trying to use the USB connectivity firmware so that I can use the pc-ble-driver with it.
I downloaded to my custom board the file 'connectivity_4.0.0_usb_with_s140_6...
Hi, I want to send 9000bytes one sencond.But when I send these bytes it will return error code is 19.
I had increased the ATT MTU to 274 with the function of nrf_ble_gatt_att_mtu_periph_set...
Hi everyone,
I'm playing with the nRF52840 dongle (PCA10059) but I'm not able to program it using nRF Connect (v2.6.1).
I open the sw and connect the dongle, choose...
I am trying to see onboard SD card via usbd_msc and I can not achieve that. I am sure SD card is connected properly and working as I can mount it and write files to it form...
Hello ! Hope I can get help with this as I am completely new to this and dont get a hang of it yet. What I am looking for is to be able to use the servers as clients. I have...
I use nrf52832-AA, S132
I use Fstorage from 0x68000 to 0x73FFF in flash memory.
Reading or writing data from that memory.
It doesn't have any problem working normally...
Hello Everyone,
I am newbie to nordic BLE environment. This maybe a silly question.
Currently I am using nrf51 DK with SDK11, S130.
Data to be sent through SPI:
...
Hi,
I was trying to add generic onoff server model to the dimming server example in order to On/OFF and Dim the LED on the nRF52 Dev board using nRF Mesh App. I added all...
With 100 battery powered bluetooth long range slave nodes connected to one master. To increase battery lifetime, Is is best to connect/disconnect all slave nodes to the master...
Hello,
I have the following scenario:
The device boots and starts to advertise.
When the central (android phone or iPhone) connects, peripheral requests bonding and...
I am using sdk 11, s130, nrf 51822.
Before getting into the question I ask in the title, I would like to ask this first:
1. Is it correct that every time I call pm_peer_delete_all...
