I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
I want to check out the long attributes capabilities of the S110 SoftDevice.
Inside of the Sdk 5.2.0, I cannot find an appropriate example.
I'd found some example code here...
Hi,
How to work with the connectable directed advertisement (BLE_GAP_ADV_TYPE_ADV_DIRECT_IND) event?
I modified the ble_app_template application to support direct advertisement...
Hi,
I am developing a test board with a nRF51822 and ST balun (NRF01D3) and a chip antenna (probably Johanson 2450AT18A100 or B100). The board will have 4-layers. The inner...
nrfgostudio_win-32_1.15.1 program softdevice s110_nrf51822_6.0.0_softdevice.hex works well with STlink for nrf51822 but when I program bootloard error appear :
Running...
Hi,
I'm using the redbearlab shield in combination with an arduino uno r3.
I want to send sensor data at about 10 hz to my smartphone.
This works but sometimes I get...
Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hello,
I am trying to get the PCA10001 evaluation board going with BLE, and am trying the ble_app_hrs example from the SDK as a start. I am developing on Mac OS with Eclipse...
Im trying to have the s120 modify the value like I would in Do a Read all records operation in the Glucose example. I cannot figure out what function would enable me to do...
The SDK function sd_ble_uuid_vs_add may return NRF_ERROR_INVALID_ADDR If p_vs_uuid or p_uuid_type is NULL or invalid.
When the pointer is not NULL, how does this function...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi we are using NRF51822 board.
i flash ble_app_hrs application. then it is giving advertisement.
but when i call twi_master_init() function from main. advertisement...
szenario
beacon and receiving nodes are all MCU based and all powered by net, no local battery needed
the beacon usually located near the floor, the nodes will be located...
Blicky project runs and I can set break points and run through them - watching the LEDs blink appropriately. However, the HRS and Proximity projects will successfully load...
Hi all,
I'm using the LE1 to do the mutilceiver,if I donn't use the dynamic payload,I can do it successfully.However,if I use the dynamic payload to do Multiceiver,the...
Hi,
For the LE1,I found that 32.768kHz crystal oscillator need long time(about 350ms) to running,I must do some delay(about 350ms) for the software then use the RTC,or...
