After ping through link local address ,i am not getting any Router solicitation messages,neighbor solicitation messages and neighbor advertisement messages while i am capturing...
Hi I've got my nRF8001 breakout board ready I now need the SDK in order to start developing firmware code.
I don't have any registration key, how do I get hold of it? ...
Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
Hi,
My ultimate goal is to add NDT [1] to a meshtastic [2] device implemented with RAK4631[3]. For this goal I can see the following obstacles:
- The meshtastic stack...
Hi,
I am trying to modify the ble_app_blinky example in such a way that I can connect with multiple central devices to on peripheral device.
So far I found a good start...
From "nrf_section.h" (__GNUC__):
Example for the section name " log_const_data ":
NRF_SECTION_DEF(log_const_data, nrf_log_module_const_data_t) //: extern nrf_log_module_const_data_t...
I am using NCS Connect SDK version 2.6.0
I am trying to create an array of models and found a problem with using Zephry macros in C++ projects. My main.cpp is as below ...
I have a sample app (hellow world from the zephyr samples).
It compiled well on my system in vscode using 2.7.0 and sysbuild.
I then installed 2.8.0 and suddenly the build...
Hi,
I just got nRF54L15 Development Kit boards. I installed 2.8.0 nRF Connect SDK and toolchain into VS Code. I was using 2.6.1 versions,
with nRF52840 and nRF5340 DK...
Am making a project based on NUS central demo and I can connect to our remote unit with the 52840DK, I can send data over a UART into it and I can get data out which is received...
Hi Community,
I made a custom board based on thingy53, created a similar custom board file folder.
The application code can be compiled correctly with the original thingy53...
I am using NRF Connect for VS Code on Ubuntu 24.02 with an adafruit nrf52840 feather express. When attempting to use the DeviceTree Extension, the wrong dts file is listed...
Hello,
We are using the npm1300 with a battery with an NTC.
Can we add a ferrite between battery NTC and npm1300 NTC?
Note: there is an error in our design we will...
I have managed to get, somehow, a central_uart talking to a peripheral_uart on a pair of 52840 DKs.
I've changed the UUIDs of what I'm trying to connect to, to be those...
Hello!
I built the https sample app for the Sparkfun_I got run time errors.
my setup:
Updated Windows 11 Pro
SDK 2.6.1 and 2.8.0
How do I solve this?
"The Modem...
Hi,
I am using a Proteus-e module from Wurth Elektronik for a project. This module contains a nRF52805 chip. I am using the nRF Connect app to send commands to configure...
Hello.
I'm trying to enable MCUBOOT in my project.
I added CONFIG_BOOTLOADER_MCUBOOT=y to the prj.conf, but I'm getting the next message: " BOOTLOADER_MCUBOOT set more...
