After ping through link local address ,i am not getting any Router solicitation messages,neighbor solicitation messages and neighbor advertisement messages while i am capturing...
Hi I've got my nRF8001 breakout board ready I now need the SDK in order to start developing firmware code.
I don't have any registration key, how do I get hold of it? ...
Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
Hi,
1. Can nRF52840 run RCP+BLE at the same time? 2. Are there any examples you can provide to customers? 3. Are FLASH and RAM sufficient for resources?
Thank you for...
Hi,
Currently, I am working on ble_app_bps code and I alter it to be act as a beacon code and I can able to store a data in the flash memory area 0x30000 and it works fine...
FreeRTOS Kernel V10.0.0 MCU: nRF52840 SDK 17.1.0
Our device is fully functional, and we are currently performing various tests. During long-term testing, we found that...
I'm building a project based on the example: C:\Users\leand\OneDrive\Documentos\TesteBLEDual\nRF5_SDK_17.1.0_ddde560\nRF5_SDK_17.1.0_ddde560\examples\ble_peripheral\ble_app_hrs...
I'm running V2.60 NCD on a custom n5340 processor and I can't decipher what is the proper device tree based on the examples.
I have a 10 button keypad and want to detect...
Dear Tech,
I am using the pre release version of the VS Code plugin and NCS v2.7.0 for development. Our team hopes to develop the product based the official version to ensure...
Hello Everyone,
I used the HRS application example for LESC secure communication and added the OTA to the HRS application. After adding that, the device restarts. I debugged...
I am programming now nrf52810 I try to merge uart functionality to ble_app_blinky project but it does not work i debug and found out uar_error_handler() never been reached...
Hi.
I am using a custom board on the nRF52820 microcontroller (wiring diagram in the figure). When the microcontroller is powered only from the battery (via external LDO...
Document: HTTPS_SAMPLE_2024_09_19T02_55_15_089Z.txt I was programming the HTTPS sample with default parameters. I managed to connect to "example.com successfully". I managed...
I'm working on a BLE project based off of the peripheral_lbs sample within the nRF Connect SDK v2.7.0. I am attempting to increase the BLE security level up to either level...
Hi,
I am working on a battery powered device that collects data, save it to files and go to sleep, when it is not connected to a laptop via USB. When connected, the device...
Hi,
I want to change the LED pin that blinks to indicate BLE advertisement to pin 6. I have changed the LED_1 and LED_STOP in pca10040.h to 6:
I have also set NRF_LOG_BACKEND_UART_ENABLED...
Hi.
I am developing a custom board using nRF52840 inside a Moko MK08A and an accelerometer LIS2DH.
My circuit has a 3V3 voltage regulator just for the LIS. The microcontroller...
Hello
I'm trying to connect muy Power Profiler Kit II to my PC, and when I choose the device from the list it pops-up:
I clicked 'Program' and after I supposed it...
