I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
When using nrf51-ble-driver_win_0.3.0 with Visual Studio 2010, after I put a breakpoint in my code, when I try to have the process "continue", I always get unandles exception...
Dear sirs,
Many thanks for the IoT SDK.
Just setting up the Raspberry I can't start the Phyton CoAP example as defined in documentation.
The envirinment is:
R...
Hello everybody,
I'm getting crazy, I'm trying to extend HID axis values from 0..255 to 0..1023 max using the descriptor found in the example ble_HID_keboard/hid_joystick...
Hi, I'm testing the beacon example
(ble_app_beacon, Beacon Transmitter Sample Application ) with my custom board.
I use IAR 7.1 for ARM, Softdevice S110 ver 7.1, and...
Hi,
I'm trying out S130 SoftDevice. I have 1 device with S110v7 which acts as a peripheral.
2nd device contains S130 0.9 (I've based my code on S120 multilink central example...
Hi,
We are trying to attain power optimization in our project, which uses the nRF5340 board. In our code we have implimented RTOS, BLE for data transfer and are using i2c...
Hi,
I encountered an issue since i upgraded nrfjrpog
My previous version was 10.13.0
And now is 10.24.2.
I have a batch file to program my device and until the upgrade...
We need very fast Wi-Fi transfer rates at times. I have been able to tune the code and Wi-Fi driver settings to get up to 30-35 Mbps which is great. But if I don't throttle...
Hi,
Added a function to the coap_client sample code that executes otInstanceFactoryReset by pressing a button and sets it to factory shipping mode. However, it appears that...
I'm developing a system where I want to connect simultaneously to different BLE and ANT+ sensors. I'm using the nRF5340 DK and I would like to be able to select which sensors...
I have a project that I'm pulling in code from multiple_adv_sets using v2.7.0 and sysbuild.
talks about the opcodes and status being in the spec? https://www.bluetooth...
Hello,
We are designing a board with a npm1300 and a nRF5340. A button is connected to npm1300 SHPHLD.
On short-press, we want the npm1300 to send an interrupt to the...
Hi team,
We tested the nRF7002 with the nRF5340 as the host. Now, our application needs to connect the nRF7002 Wi-Fi module with a custom microcontroller other than Nordic...
Hello,
I am trying to establish communication between the nRF9160 SoC and the nRF52840 on the Thingy:91. I have two arrays: one of 774 bytes and another of 8 bytes. Currently...
In the Wi-Fi Fundamentals Course, Lesson 2, Exercise 2 (step 7.2) I found that it is necessary to clear the bssid parameter in the wifi_connect_req_params structure. If it...
Message:
Hi Nordic Semiconductor Dev Zone,
I am developing a PCB that mirrors the one in Sony WF-1000XM5 earbuds, but with the microcontroller replaced by the nRF9161...
I use NRF52832 as a Bluetooth gateway to receive commands and initiate connections to devices. Each instruction received will be interrupted through the IO pin, and the MAC...
OS: Window11
Programmer version : v4.4.0
Used Chip: nRF5340
Used Hex file: peripheral_uart_nrf5340dk.hex
An error occurred while Erase&Write the Hex file while testing...
The default setting for the external flash chip of 9160dk appears to be 64m, but when used, the log display only shows 8m, and only the part within 8m can be used,
Then...
