Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
Hi,
I'm using nRF9160dk to configure MQTT . i'm new to MQTT so ,Is their any example code to understand and work on it by using " ZEPHYR RTOS "
thanks in advance.
A product I'm working on uses an nRF5340 (actually a Fanstel BT40 module with an nRF5340 in it) with NCS v1.7.1.
It's got an SPI slave connection (the nRF is the slave)...
good day,
is there a guide or tutorial on how to detect different press type in single button? will try to assign different tasks per button press types (single, double...
Hi Support team,
According our spec 52832 rx is about 5.4mA, but actually i measured our example, it is about 7.1mA, may i ask where is the gap? so i suspect it is because...
Hi,
I'm developing an application based on the nRF52832 development kit. It is nrf52dk_nrf52832(PCA10040). I have used nRF Connect SDK (3.0.0) for the project development...
Hello,
I am trying to interface the ble_hid_keyboard with uart using nrf52840-Dk in SDK 17.0.2. But not able to print data from uart and even not able to connect hid keyboard...
Hi,
I have an nRF9160 and working am off of the AWS_IOT sample code. When I start the device, the error messages occur 2-3 times and then the device connects successfully...
Hi,
I'm working on a custom board with a nrf9160 µC. This board is powered by a battery and a supercapacitor and my job is to assure the autonomy of the battery.
I...
I am using 9160 to develop a product for customers, which saves the date, time and other settings in NVS. Yesterday, I encountered a problem that the product could not start...
Hi Nordic team,
Is there any sample project which implements DFU controller in nRF52832 central device? I need to update peripheral device firmware from central device...
We are using SDK 17.1.0 with SoC nRF52832 and Soft Device S132.
We want to configure the soft device to enable the TX and RX GPIOs to talk to off-chip power amplifier. Looks...
Hello there. I would like to know how can I read the counter value right before resetting WDT directly from the register.
That means right before calling:
I want to know...
Hello,
I'm developing a NB-IOT application on the nRF9160-DK based on the 2.6.1-rc1 SDK. I'm experiencing a bug where the firmware gets stuck while serving a send() request...
I am successfully able to use pc-ble-driver on nRF52840 Preview DK using latest connectivity firmware loaded by nRF Connect.
I want to use the same functionality on FENSTEL...
I am using the nRF52840 (with SDKv17.0.2 + s140_7.2.0) and made a custom FW based on the ble_app_hrs example. My custom HW has a 128MB MX66U1G45G flash memory chip.
The...
