Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
Hello Everyone,
I am using nrf52832 and sdk 15.2 for BLE scanning and advertising. scanning and advertising is working parallel. this is controlled by other MCU over serial...
Hello,
I was able many times to download nrf52-ble-image-transfer-demo-master in to nRF52840 DK (PCA100156) and run a mobile application successfully.
Today I downloaded...
Hi ! I'm using nrf52 + SDK 17.1.0.
I found sd_mutex_acquire/ sd_mutex_release, which is great for locking variables that are set/get asynchronously. Next, I'd like to use...
Hi, I'm using nrf52840DK.
I set the selective_auto_ack as true. It should be able to adopt dynamic ack (or ack payload).
I have two data packets, which are ch_pkt and...
Hello,
I try to figure out, why a certain IO pin shows some pattern at startup. After using JLinkExe to set a watchpoint at the configuration register of the pin (GDB was...
I am trying to update my firmware using IOS-nRF-Connect-Device-Manager and am getting an invalidHeaderMagic error when calling: I am using version 1.7.3 (last version to still...
I'm attempting to use the Settings API save and retrieve data from nRF52832 FLASH memory. I can build and run the example application provided in the Settings documentation...
Hello Developers,
I am working with the nRF52833 microcontroller using segger embedded studio with the latest SDK. My issue is that I can configure and use all GPIOs except...
I have browsing this site, no clearly answer found, but,I think someone has done this job before.
My scenario:
.many BLE client (5.0 above);
.BLE clinet will upload...
Hi, We have an application running on the nRF53, and would like to change the BLE MAC address from the default Random Static Address, to a Public Address with a valid Vendor...
I'm studying with PCA10059,trying to build a gateway between BLE peripherals & PC.
For PCA10059 has build-in USB socket,and I will plug them into PC's USB ports at last...
Hi all,
I want to use UART periodically, but because I need to communicate with other standard UART, I cannot use LPUART
I saw that Zephyr's demos all use CONF_SERIAL...
I am following all the steps given here: nRF Sniffer for 802.15.4 but my zigbee sniffer did not show up. When i did the steps given there for ble sniffer it showed up. steps...
Hello,
I am new to developing with Nordic products and I have a question regarding the components in the antenna matching network. I am designing around the QIAA QFN-73...
Hi,
I am trying to use the nRF915-DK with a GNSS Tracker application. Everything works fine, but, I am not able to set the nRF9151-DK properly for utilizing the board...
