After ping through link local address ,i am not getting any Router solicitation messages,neighbor solicitation messages and neighbor advertisement messages while i am capturing...
Hi I've got my nRF8001 breakout board ready I now need the SDK in order to start developing firmware code.
I don't have any registration key, how do I get hold of it? ...
Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
hardware: NRF52832
SDK:17.02
I'm trying to get SPIM working with a RF(SX126). I'm currently trying to use the nrf_drv_spi_transfer() function.
I need to read and write...
Hello everyone,
I have a problem with my device name. First of all I want tro write the device ID into the device name. I get the device ID over "RF_FICR->DEVICEID[0]"....
Dear Members,
How can I stop ANT HRM channel temporarily, and save the heart rate value on to SDcard ?
My code at static void page0_data_log(ant_hrm_page0_data_t const...
Hello,
I’m designing a custom nrf52832 device and i came across an issue with energy buffering. I am using inside of the device the battery CR2032, SoC nrf52832 and two...
Hello,
I've successfully setup a development environment for nRF Connect and Zephyr on windows (VS Code extension) where I can build, debug and flash code to my board...
The nRF52833 isn't supported Bluetooth low energy by nRF Connect for Desktop as list device in link https://infocenter.nordicsemi.com/index.jsp?topic=%2Fug_nrfconnect_ble...
Hi, I'm working on nRF52840-DK board and NCS SDK-v1.7.0 on Windows with Visual Studio Code.
We want to add support for Image validation for imaged signed with ECC curve...
Hello,
I have nRF Connect Desktop v3.9.1 for MacOS installed. I am trying to run the "Bluetooth Low Energy" utility using a nRF52840 dongle.
If the only device connected...
Hello
I was trying to get this example ble_app_template to work but it seems like it doesn't, the code is executed on the ic since I was uploading some code to blink a light...
Hi,
I have a question about running a secure service that does RSA encryption and decryption in SPM using mbedTLS.
I am using SEGGER Embedded Studio for ARM (Nordic Edition...
Hello all, Currently I am developing a code in which a central (nRF52840) scans and reads adverisement packets from 2 beacons (no connection required). I decided to use an...
Using nRF52832, I've got some firmware that uses NFC pins (9 & 10) without problem, using CONFIG_NFCT_PINS_AS_GPIOS.
I'm now trying to replicate this using nRF52833, and...
I am working with the nRF52840 under Zephyr to develop some wireless sensors. The issue I am having I build a test module using the nrf/samples/light. This running on the...
Hello,
I've been experimenting with nRF Connect SDK and compiling a program which supports provisioner mode, provisioning and direction finding.
Everything compiles and...
Hi everyone,
I work with an nrf52840 and SDK15.3.0 and SD 140-6.1.1
I have a board with two micro controler, one nrf52840 and one STM32.
I want to know if it is possible...
