Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
Hi, using the Nordic power profiler 2 (PP2) kit to measure the current draw of my nRF52833 DK. I have followed the instructions to setup/prepare/wire the PP2 to my DK and...
In the task, when I do a TWI read via nrf_drv_twi_rx(), in the second iteration of the thread, the driver function returns NRF_ERROR_BUSY.
Is it that the driver takes longer...
I've built a custom board using nRF52832 which uses SDK 16.0.0 and softdevice version s113. A part of application is audio streaming/ decibel calculation and transmission...
Hall Mr. Nordic,
I'm sending a 16bit payload with 51822.
The receiver 24L01 is receiving all perfectly. The receiver 52840 is loosing the first two bytes ...
nRF51822...
Hi,
I'm using nRF52840 as my server and the android mobile is my client. At the client end, I'm using the nRF Connect app. It seems like the 50 bytes of data is taking around...
Hello,
I have an nRF9160 DK board (I believe the version is PCA10090 1.0.0) and would like to use the external flash that comes with this board.
Upon inspection, this...
Hi,
I'm seeking help on debugging the network core with Visual Studio Code. My project is not based on a standard SDK and hence I think VS code will be easier to setup than...
hello!
I have an issue, I need to read data from a Module, then I send that data using USBD..
when I put that code in for(;;) before while(true) the port is activated...
The nRF52840 DK has a 64 mbit external flash on board. The MX25R6435F.
It's performance is too low, in terms of erase speeds - It takes several minutes to erase the entire...
I'm trying to upload hex files to my NRF52832 with nrfjprog in command line and got the following error:
My log file:
I've been searching and searching, but could...
Hello,
I am new to the NRF52 SoC and BLE development. I've been using the ble_app_template and following along this tutorial to learn more about BLE development. I'm having...
I am developing a mobile application using React Native.
I wish to integrate a 'lost tag' functionality using a BLE tag.
The BLE tag will be placed near the item of interest...
Hi, The purpose of this is to have a software Power ON/OFF button, when I first start the firmware, it automatically goes OFF. Then after a long press on the button, it should...
I am using nrf52832 controller and interface with MAX30102 sensor. when i tried to read heart rate in nrf connect application , it shows Sensor Contact not supported.
