I ran the ble_aci_Tranport_layer_Verification.ino sketch from the Nordic BLE library and I get no output to the serial monitor after "nRF8001 Reset Done" is displayed. I think...
I am trying to debug my code today and am finding that Eclipse is constantly breaking execution at the INLINE function app_timer_evt_get(). I do not have any break point set...
Hi,
Recently,
the DFU of the "Master Control Panel" (Android) can not complete the upload mission.
But,
the DFU of the nRF-Toolbox in iOS is
work well.
Old...
I just tried out the new iOS nRF Toolbox 1.5 and it doesn't seem to handle long init packets.
I gave it a zip file that contains a 137216 byte 'application.bin' and a 192...
Hello everybody,
In the SD_EVT_IRQn ISR I check for BLE and SoC events and set flags for each so my application can fetch and dispatch the events in the main context. ...
Hi, in the example bootloader in sdk 7.2, there is an assembly code block in SVC_Handler, in dfu_ble_svc.c.
I found that the offset in line:
LDR R0, [R1, #24]
always...
In nRF51 SDK 7.1.0, there is a c header file using c++ keywords operator .
Here is a snippet of components/ble/ble_racp/ble_racp.h using the keywords.
/**@brief Record...
What is the drawback of setting the TTL on mesh packet to a high number?
I am assuming that a node will not relay the same message twice? I.e. it sees a packet for the first...
Hello!
I’m quite new to the nRF microchips and am trying to programme my nRF52-DK board following this guide ( https://infocenter.nordicsemi.com/pdf/getting_started_keil...
We are working on the OTA DFU of NRF52840. The soft device version we use is the latest: s140_nrf52_7.2.0.
Unfortunately, nrfutil does not have the code number for this...
Hello
Based on this example : https://devzone.nordicsemi.com/f/nordic-q-a/57881/store-custom-application-data-using-peer-manager?ReplyFilter=Answers&ReplySortBy=Answers&ReplySortOrder...
Hi Support,
I am observing something that is quite strange on the GPIO input. I am developing a Zigbee device with Energy harvester with NRF52840. I need to use the state...
In addition to uarts, I2cs and SPIs I tried toggling some apparently spare pins without seeing voltage changes on the pins I tried.
Which pins are available for digital...
I'm using the Nordic nRF52840-DK board to breadboard an SDHC card interface in Zephyr using SPI. I have it doing "basic" operations, but am trying to reconcile what I'm physically...
Chip - BT832AF (nRF52810 QFAA)
SDK- nRF5_SDK_17.0.2_d674dde
SD - s112_nrf52_7.2.0
2V- power supply
My application need not to be very fast, but is extremely concerned...
Hi,
I am working on a project with 2 nrf52840 devices. One is the nrf52840 dk, while the other is a custom board with the nrf52840 module. I want to perform a dfu over uart...
I think this is a very weird requirement
Normally , I use manufacturer data to do this like picture below
it's easy and quick
but it contains len and type occupying...
Hey,
I am trying to get the Asset_tracker_v2 running on my Thingy:91, but with my own Cloud connection (It is a Thingsboard CE hosted on an ubuntu Server in Open Telekom...
I have to execute some lightweight error correction codes (ideally BCH) to compare and subsequently correct the mismatches between two binary arrays. I am working on the nrf52840...
I have been testing lte_lc_init_and_connect with my units inside a Faraday cage, This method doesn't terminate when it cannot get a signal (at least I haven't seen it). This...
I am attempting to install the nRF Connect SDK v1.5.0 on Mac OS X Big Sur, I have followed the Getting Started Assistant and Toolchain Manager with no success.
Here is my...
