Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
Based on zigbee sdk 4.1, in the sample code of light_switch, leaving the network and joining the network are completed by buttons, the code is as follows:
Seen from the...
Hi, my BLE application on nRF52832 is designed to select two mode to operate with 3 position slide switch when power on like ON(Mode 1) - OFF - ON(Mode 2).
At Mode 1 position...
Hello.
I'm using nrf52840 to sample the voltage from the wireless board and then send the data to the PC via Bluetooth.
With the help of DevZone, it was able to construct...
Hi,
I have downloaded and installed nRF Connect for desktop - Bluetooth Low Energy. Now I want it to operate as a peripheral that can send connectable advertising packets...
I'm having an odd issue with libUARTe sending a TX buffer twice.
I have a custom board using an nRF52832 running an application based on SDK 15.3.0. The libUARTe code was...
Doing development on nRF52 DK board using buttonless DFU example and SDK 17.0.2. Running SES on Win10 and gnu compiler.
I've set up a 1 mS timer to run timing in my main...
I am using the ble_app_uart in combination with the f_storage example to write data to the flash memory. A issue which arises is that, when a softdevice is enabled, the nrf_fstorage_nvmc...
I am using Mesh SDK v4.2.0 and my goal is to get the device MAC from the UUID that is available from p_evt->params.unprov.device_uuid available on the prov_evt_handler callback...
I guess this should be obvious, but I still have to ask. What do XRFTEST RX and TX modes actually do? I've read the documentation and it "feels" like they command the transceiver...
Hello
It seems that we had a crash during execution of nrf_bootloader_fw_activate() in an added sub function where we program an externally connected MCU and the bootloader...
Dear Sir,
I'm use 2 nrf52840 chips to test sensitivity by nRF-DTM-1.0 tool.
I find out it's work on 1M and 2M but S8 and S2 can work.
The PER can't get 0% when I only...
Hi all,
I am developing BLE firmware to send and receive data between the development kit PCA10100 and nRFConnect App Desktop.
I'd like to notify the client (the App)...
Hi all, I am using SPIM with dma list triggered by gpiote. A gpio low-to-high event starts spim reading, and it works fine. However, I need to read different length at different...
